port-config-modify

This command is used to modify port settings on the switch.

Syntax   port-config-modify

port port-list

Specify a single port or a list of ports.

Note: If more than one port is specified, the list must be comma-separated without spaces.

Specify any of the following options:

intf intf-number

Specify a physical interface for the port.

speed disable|10m|100m|1g|
2.5g|10g|25|40g|50g|100g

Specify the port speed. Ports configured for speeds of 1G must be equipped with SFP transceivers. Ports configured for 10G or higher must be equipped with SFP+ or QSFP+ transceivers.

bw-bps bw-bps-number 

Specify the bandwidth bps for the port.

egress-rate-limit unlimited

Specify an egress rate limit for the port.

eth-mode 1000base-x|sgmii

Specify the Ethernet mode as 1000 base or Serial Gigabit Media Independent Interface (SGMII).

autoneg|no-autoneg

Specify if the port auto-negotiates the port speed with a peer.

jumbo|no-jumbo

Specify if the port forwards jumbo frames. Jumbo frames are Ethernet frames with more than 1500 bytes of payload.

enable|disable

Specify if the port is enabled and forwards or drops frames.

lacp-priority integer

Specify the LACP priority for the port. If you specify a low value for the priority, the port has a higher priority. This is a value between 1 and 65535.

reflect|no-reflect

Specify if the port reflects frames received for loopback testing.

edge-switch|
no-edge-switch

Specify if the port connects to another Pluribus Networks device or is an uplink to a third-party switch or host.

pause|no-pause

Specify if you want to pause traffic on the port.

description description-string

Specify a description for the port.

loopback|no-loopback

Specify to use loopback or no loopback.

vxlan-termination|
no-vxlan-termination

Specify if a VXLAN terminates on a port.

mirror-receive-only|
no-mirror-receive-only

Specify if the port receives mirrored traffic only.

port-mac-address mac-address 

Specify the MAC address for the physical port.

loop-vlans vlan-list

Specifies VLANs that are looping on the network.

send-port send-port-number

Specify the port to send traffic.

routing|no-routing

Specify if the port is participating in routing on the switch.

host-enable|host-disable

Specify if you want host-facing ports enabled or disabled.

crc-check-enable|crc-check-disable

Specify if you want CRC checking performed by the port. This is applicable to a switch in Virtual Wire mode. The default value is crc-check-disable.

dscp-map dscp-map name | none

Specify a DSCP map name to enable on port.

local-switching|no-local-switching

Specify if local switching is allowed on the port.

allowed-tpid q-in-q|q-in-q-old

Specify the allowed TPID in addition to 0x8100 on VLAN header

fabric-guard|no-fabric-guard

Specify if you want loop detection enabled on the port.

 

Defaults   The default port speed is 10G per second. Autonegotiation and jumbo frames are disabled by default. The port is enabled by default.

Access   CLI

History   

Version 1.2

Command introduced.

Version 1.2.6

The optional parameters for LACP added.

Version 2.1

The parameters, loopback, mirror-receive, port-mac-address, vlag-failover, and send-port added. The parameter, lacp-mode, deprecated.

Version 2.2.6

The parameter, egress-rate-limit, introduced.

Version 2.3

The parameters, rem-rswitch-port-mac, and routing|no-routing added.

Version 2.4

The parameter, host-enable, and loop-vlans added.

Version 2.4.1

The parameter, rem-port-mac-address, deprecated. The parameter, intf, added.

Version 2.5.2

The parameter, crc-check-enable|crc-check-disable, introduced.

Version 2.5.3

The parameters, reflect|no-reflect, vxlan-termination, dscp-map, and local-switching added.

Version 2.6.0

The parameter, fabric-guard, and allowed-tpid, added.

Version 3.0.0

The parameter, bw-bps, added.

Usage   Server-switches are equipped with network data ports for host or inter-switch communication. This command configures the settings of a specific network data port of all data ports on the local switch.

Examples  To configure port 17 on a switch to operate at 1 Gbps without jumbo frames, use the following command:

CLI network-admin@switch > port-config-modify port 17 speed 1G autoneg off jumbo off

See Also   

port-show

port-config-show

port-phy-show

port-stats-clear

port-stats-show

port-vlan-add

port-vlan-remove

port-vlan-show

port-xcvr-show