port-config-show

This command is used to display port settings on the switch.

Syntax   port-config-show

intf intf-number

Displays the interface number.

name name-string

If configured, displays the name of the port. Otherwise, the field is blank.

port port-list

Displays a port or list of ports.

speed disable

|10m
|100m
|1g
|2.5g
|10g
|25g
|40g
|50g
|100g

Displays the port speed. Ports configured for speeds of 1G must be equipped with SFP transceivers. Ports configured for 10G or higher must be equipped with SFP+ or QSFP+ transceivers.

egress-rate-limit unlimited

Displays the egress rate limit for the port.

bw-bps bw-bps-number 

Specify the bandwidth bps for the port.

eth-mode
1000base-x|sgmii
|disabled|1000base-kx
|2500base-x|6Gbase-kr|6Gbase-cr|10Gbase-kr
|10Gbase-cr|10Gbase-sr|AN-73|Xaui|10Gbase-kx4|10Gbase-cx4|24Gbase-kr4|24Gbase-cr4
|40Gbase-kr4|XLaui|40Gbase-cr4
|40Gbase-sr4|
no-phy-present
|MII|GMII|TBI|10G-XGMII|1G-RGMII|10G-SFI|10G-XFI

Displays the Ethernet mode.

autoneg|no-autoneg

Displays if the port auto-negotiates the port speed with a peer.

jumbo|no-jumbo

Displays if the port forwards jumbo frames. Jumbo frames are Ethernet frames with more than 1500 bytes of payload.

enable|disable

Displays if the port is enabled and forwards or drops frames.

lacp-priority integer

Displays the LACP priority for the port. This is a value between 1 and 65535 with a default value of 32768.

reflect|no-reflect

Displays if the port reflects frames received for loopback testing.

edge-switch|
no-edge-switch

Displays if the port connects to another Pluribus Networks device or is an uplink to a third-party switch or host.

pause|no-pause

Displays if the port traffic is paused or not.

description description-string

Displays a description for the port.

loopback|no-loopback

Displays to use loopback or no loopback.

vxlan-termination|
no-vxlan-termination

Displays if a VXLAN terminates on a port.

mirror-receive-only|
no-mirror-receive-only

Displays if you want the port to receive mirrored traffic only.

vle vle name

Displays the VLE on this port.

trunk-hw-id trunk-hw-id-number

DisplaysDisplaysDisplays the trunk hardware ID assigned..

trunk trunk-name

Displays the trunk name for the port.

vlag vlag-name

Displays the VLAG for the port.

send-port send-port-number

Displays the port number to send in packets.

loop-vlans vlan-list

Displays the VLANs that are looping on the network.

routing|no-routing

Displays if the port is participating in routing on the switch.

host-enable|host-disable

Displays if you want host-facing ports enabled or disabled.

crc-check-enable|crc-check-disable

Displays if you want CRC checking performed by the port. This is applicable to a switch in Virtual Wire mode. The default value is crc-check-disable.

dscp-map dscp-map name | none

Displays a DSCP map name to enable on port.

local-switching|
no-local-switching

Displays if local switching is allowed on the port.

rhost rhost-string

Displays the physical remote host.

allowed-tpid q-in-q|q-in-q-old

Specify the allowed TPID in addition to 0x8100 on VLAN header

fabric-guard|no-fabric-
guard

Displays if you want loop detection enabled on the port.

Formatting Options

format fields-to-display

Display output using a specific parameter. Use all to display all possible output.

parsable-delim character

Display output formatted for machine parsing using a specified delimiter.

sort-asc

Display output in ascending order.

sort-desc

Display output in descending order.

show dups

Display duplicate entries in the output.

layout vertical|horizontal

Format the output in a vertical or horizontal layout.

show-interval seconds-interval

Repeat the show command at a specified interval.

show-headers|
no-show-headers

Display column headers or not.

limit-output number

Limit the display output to a specific number of entries.

count-output

Display the number of entries in the output. This is useful with vRouter show commands.

unscaled

Display full values in the output instead of scaled approximate values.

raw-int-values

Display integer values instead of mapped values

sum-by

Aggregate output by specific parameters. If sum-by fields are specified, records that have the same value in sum-by fields are combined and displayed as one aggregate record. NOTE: This option is only available for show commands that collect statistics such as connection-stats-show.

Defaults:None.

Access:CLI

History:

Version 1.2

Command introduced.

Version 1.2.6

The optional parameters for LACP added.

Version 2.1

The parameters, loopback, mirror-receive, vlag-failover, and send-port added.

Version 2.2.6

The parameter, egress-rate-limit, introduced.

Version 2.3.1

Multiple parameters for LACP added.

Version 2.4

The parameter, host-enable, and loop-vlans added.

Version 2.4.1

The parameters, lacp-fallback, lacp-fallback-timeout and lacp-individual deprecated.

Version 2.5.2

The parameter, crc-check-enable|crc-check-disable, introduced.

Version 2.5.3

The parameters, reflect|no-reflect, vxlan-termination, dscp-map, and local-switching added.

Version 2.6.0

The parameter, fabric-guard, and allowed-tpid, added.

Version 3.0.0

The parameter, bw-bps, added.

Usage:Server-switches are equipped with network data ports for host
or inter-switch communication. This command configures the settings of a specific
network data port of all data ports on the local switch.

Examples:To display information about all ports on a switch, use the following command:

CLI network-admin@switch > port-config-show

switch:                pleiades25

intf:                  10

name:                  

port:                  10

speed:                 10g

autoneg:               off

jumbo:                 off

enable:                on

lacp-priority:         32768

reflect:               off

edge-switch:           no

pause:                 no

description:           

loopback:              default

mirror_only:           default

rswitch-default-vlan:  0

port-mac-address:      06:b0:00:02:30:0a

 

See Also: