This command displays the list of links aggregated into a trunk.

Syntax   trunk-show

intf intf-number

Specifies the interface number.

name name-string

Specifies the name for the trunk configuration.

port port-list

Specifies the port number(s) for the link(s) to aggregate into the trunk.

speed disable|100m|1g|10g|40g

Specifies the port speed or disable the port.

egress-rate-limit unlimited

Specifies if an egress rate limit is configured.


Specifies if the physical port autonegotiates port speed.

eth-mode 1000base-x|sgmii|disabled|1000base-kx|2500base-x|6Gbase-kr| 6Gbase-cr|10Gbase-kr|10Gbase-cr|10Gbase-sr|AN-73|Xaui| 10Gbase-kx4|10Gbase-cx4|24Gbase-kr4|24Gbase-cr4|40Gbase-kr4| XLaui|40Gbase-cr4|40Gbase-sr4|no-phy-present|

Specifies the Ethernet mode for the trunk.


Specifies if the port auto negotiates network traffic or does not.



Specifies if the port can receive jumbo frames.


Specifies if the physical port is enabled or disabled.

lacp-mode off|passive|active

Specifies the Link Aggregation Control Protocol (LACP) mode for the configuration.

lacp-priority number

Specifies the LACP priority. This is a number between 1 and 65535.

lacp-timeout slow|fast

Specifies the LACP time out as slow (30 seconds) or fast (4 seconds).

lacp-timeout slow|fast

Specify the LACP time out as slow (30 seconds) or fast (4 seconds). The default value is slow.

lacp-fallback bundle|individual

Specify the LACP fallback mode as individual or bundled.

lacp-fallback-timeout seconds

Specify the LACP fallback timeout in seconds. The range is between 30 and 60 seconds with a default value of 50 seconds.


Specify physical port reflection


Specifies if the switch is an edge switch.


Specifies if pause frames are sent.


Specify if a VXLAN can terminate on the trunk.

unknown-ucast-level unknown-ucast-level-string

Specify an unknown unicast level in percent. The default value is 100%.

unknown-mcast-level unknown-mcast-level-string

Specify an unknown multicast level in percent. The default value is 100%.

broadcast-level broadcast-level-string

Specify a broadcast level in percent. The default value is 100%.

rem-rswitch-port-mac mac-address

Specify a remote physical port MAC address.

description description-string

Specifies a description for the trunk configuration.


Specifies loopback if you want to use loopback.

vlag vlag-name

Specifies the name of a VLAG.

trunk-hw-id trunk-hw-id-number

Specifies the trunk hardware ID.

send-port send-port-number

Specifies the port to send traffic.

loop-vlans vlan-list

Specify a list of VLANS for looping.


Specifies if the port participates in routing on the network.


Enable or disable host facing ports.

dscp-map dscp-map name|none

Specify the DSCP map name to enable on a port


Specify local-switching or no-local-switching. A no-local-switching port cannot bridge traffic to another no-local-switching port

allowed-tpid q-in-q|q-in-q-old

Specify an allowed TPID in addition to 0x8100 for VLAN headers.


Specify if fabric guard is enabled.


Formatting Options

format fields-to-display

Display output using a specific parameter. Use all to display all possible output.

parsable-delim character

Display output formatted for machine parsing using a specified delimiter.


Display output in ascending order.


Display output in descending order.

show dups

Display duplicate entries in the output.

layout vertical|horizontal

Format the output in a vertical or horizontal layout.

show-interval seconds-interval

Repeat the show command at a specified interval.


Display column headers or not.

limit-output number

Limit the display output to a specific number of entries.


Display the number of entries in the output. This is useful with vRouter show commands.


Display full values in the output instead of scaled approximate values.


Display integer values instead of mapped values


Aggregate output by specific parameters. If sum-by fields are specified, records that have the same value in sum-by fields are combined and displayed as one aggregate record. NOTE: This option is only available for show commands that collect statistics such as connection-stats-show.

Defaults   None.

Access   CLI


Version 1.2

Command introduced.

Version 1.2.6

The optional parameter, lacp-mode, was added.

Version 2.1

The parameter id is deprecated. The parameters, intf, enable | disable, lacp-priority, lacp-timeout, reflect, edge-switch, pause, description, loopback, mirror-receive, port-mac, and send-port added.

Version 2.2.5

The parameters, unknown-ucast-level, unknown-mcast-level, and broadcast-level added.

Version 2.2.6

The parameter, egress-rate-limit, added.

Version 2.3

The parameters, auto-neg, eth-mode, and reflect deprecated.The parameter, rem-rswitch-port and routing, added.

Version 2.4

The parameters, loop-vlans and host-enable, added. The parameters, unknown-ucast-level, unknown-mcast-level, broadcast-level, and rem-rswitch-port-mac deprecated.

Version 2.5.3

The parameter, reflect|no-reflect, added.

Version 2.6.2

The parameter, vxlan-termination, allowed-tpid, and fabric-guard, added. The parameter, mirror-receive-only, deprecated.

Version 3.0.0

The parameter, autoneg|no-autoneg, added.

Usage   Trunks can be used to aggregate network links at Layer 2 on the local switch. Use this command to modify the links for a trunk.

Examples  To display a list of all trunks and the aggregated links, use the following command:

CLI network-admin@switch > trunk-show

switch:               pubdev01

intf:                 128

name:                 trunk-top

port:                 26,47-48

speed:                10g

autoneg:              off

jumbo:                off

enable:               off

lacp-mode:            off

lacp-priority:        32768

lacp-timeout:         slow

reflect:              off

edge-switch:          no

pause:                no


loopback:             off

mirror-only:          off

unknown-ucast-level:  100%

unknown-mcast-level:  100%

broadcast-level:      100%

lport:                0

rswitch-default-vlan: 0

port-mac-address:     06:a0:00:03:00:80

status:               up,PN-switch,PN-fabric,PN-cluster

config:               fd

send-port:            26


See Also