vrouter-bgp-show

This command displays Border Gateway Protocol (BGP) information for a virtual router (vRouter) service on a fabric, cluster, or standalone switch.

Syntax   vrouter-bgp-show

vrouter-name name-string

Specifies a name for the vRouter service.

Displays the following BGP arguments:

neighbor ip-address

Specifies a neighbor IP address to use for BGP filtering.

remote-as remote-as-number

Specifies the remote Autonomous System (AS) number.

next-hop-self|
no-next-hop-self

Specifies if the next-hop is the same router or not.

password password-string

Specifies a password, if desired.

ebgp-multihop number

Specifies a value for external BGP to accept or attempt BGP connections to external peers, not directly connected, on the network. This is a value between 1 and 255.

update-source vrouter loopback-interface ip

Specifies the source IP address of BGP packets sent by the router. This parameter is required if you want BGP to perform peering over a loopback interface.

prefix-list-in vrouter prefix-list name

Specifies the prefix list to filter traffic inbound.

prefix-list-out vrouter prefix-list name

Specifies the prefix list to filter traffic outbound.

route-reflector-client|
no-route-reflector-
client

Specifies if a route reflector client is used.

override-capability|
no-override-capability

Specifies if you want to override capability.

soft-reconfig-inbound|
no-soft-reconfig-
inbound

Specifies if you want a soft reconfiguration of inbound routes.

max-prefix max-prefix-number

Specifies the maximum number of prefixes.

max-prefix-warn-only|
no-max-prefix-warn-only

Specifies if you want a warning message when the maximum number of prefixes is exceeded.

bfd|no-bfd

Specifies if BFD is enabled.

bfd-multihop|no-bfd-multihop

Specify if you want to always use BFD multihop port for fault detection.

multi-protocol ipv4-unicast|ipv6-unicast

Specify a multi-protocol for BGP.

weight none

Specify a default weight value between 0 and 65535 for the neighbor routes.

default-originate|
no-default-originate

Specify if you want to announce default routes to the neighbor or not.

neighbor-keepalive-interval seconds

Specify the BGP keepalive interval in seconds. This is a value between 0 and 65535 seconds.

neighbor-holdtime seconds

Specify the BGP neighbor hold time in seconds. This is a value between 0 and 65535 seconds.

route-map-in vrouter route-map name

Specify the name of the route map for incoming routes.

route-map-out vrouter route-map name

Specify the name of the route map for outgoing routes.

allowas-in|no-allowas-in

Specify if you want to reject routes with local AS in AS_PATH. Normally, when you do not set this option, nodes reject routes containing their own AS which helps prevent routing loops. However, in some cases nodes that belong to the same AS have no direct connectivity; for example when you form clusters and choose not to use the cluster link for iBGP communication. In this case the only way to direct routes through connected eBGP neighbors is to set this option so that routes are not rejected from the cluster peer.

interface vrouter interface nic

Specify the interface to reach the neighbor.

Formatting Options

format fields-to-display

Display output using a specific parameter. Use all to display all possible output.

parsable-delim character

Display output formatted for machine parsing using a specified delimiter.

sort-asc

Display output in ascending order.

sort-desc

Display output in descending order.

show dups

Display duplicate entries in the output.

layout vertical|horizontal

Format the output in a vertical or horizontal layout.

show-interval seconds-interval

Repeat the show command at a specified interval.

show-headers|
no-show-headers

Display column headers or not.

limit-output number

Limit the display output to a specific number of entries.

count-output

Display the number of entries in the output. This is useful with vRouter show commands.

unscaled

Display full values in the output instead of scaled approximate values.

raw-int-values

Display integer values instead of mapped values

sum-by

Aggregate output by specific parameters. If sum-by fields are specified, records that have the same value in sum-by fields are combined and displayed as one aggregate record. NOTE: This option is only available for show commands that collect statistics such as connection-stats-show.

Defaults   None.

Access   CLI

History   .

Version 1.2

Command introduced.

Version 2.2

Parameters next-hop-self and password added.

Version 2.2.2

The parameters, ebgp-multihop, and update-source vrouter, added.

Version 2.2.3

The parameters, prefix-list-in and prefix-list-out added. The parameters, override-capability, soft-reconfig-inbound, max-prefix, and max-prefix-warn added.

Version 2.2.6

The parameters, bfd|no-bfd, added.

Version 2.3.1

The parameter, multi-protocol, added.

Version 2.4

The parameters, weight and default-originate added. The parameters, neighbor-keepalive-interval, neighbor-holdtime, route-map-in vrouter, and route-map-out vrouter, added.

Version 2.4.1

The options, ipv4-multicast|ipv6-multicast| vpnv4-unicast, are deprecated for multi-protocol.

Version 2.5.2

The parameter, allowas-in|no-allowas-in, added.

Version 2.6.2

The parameters, bfd-multihop and interface, added.

Usage   Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a vRouter service that forwards traffic between networks and implements Layer 4 protocols. Use this command to display information about BGP on the vRouter service.

Examples  To display all BGP vRouter service information, use the following command:

CLI network-admin@switch > vrouter-bgp-show layout vertical

See Also   

vrouter-create

vrouter-delete

vrouter-migrate

vrouter-modify

vrouter-show

vrouter-bgp-add

vrouter-bgp-remove

vrouter-igmp-static-join-add

vrouter-igmp-static-join-remove

vrouter-igmp-static-join-show

vrouter-interface-add

vrouter-interface-modify

vrouter-interface-remove

vrouter-interface-show

vrouter-ospf-add

vrouter-ospf-remove

vrouter-ospf-show

vrouter-ospf-neighbor-show

vrouter-rip-add

vrouter-rip-remove

vrouter-rip-show

vrouter-static-route-add

vrouter-static-route-remove

vrouter-static-route-show