l3-history-show

This command displays historical information about Layer 3 entries on the switch.

Syntax   l3-history-show

time date/time: yyyy-mm-ddThh:mm:ss

Specifies a point in tjme for displaying historical information.

start-time date/time: yyyy-mm-ddThh:mm:ss

Specifies the start time for Layer 3 history collection.

end-time date/time: yyyy-mm-ddThh:mm:ss

Specifies the end time for Layer 3 history collection.

duration duration: #d#h#m#s

Specifies the duration to collect the Layer 3 history.

interval duration: #d#h#m#s

Specifies the intervals that data is collected Layer 3 history.

since-start

Specifies to display all of the Layer 3 history since collection began on the fabric.

time date/time: yyyy-mm-ddThh:mm:ss

Specifies a point in tjme for displaying historical information.

start-time date/time: yyyy-mm-ddThh:mm:ss

Specifies the start time for Layer 3 history collection.

log-type l2-save|l3-save|restart|
l2-modify|l2-delete|l3-modify|
l3-delete

Filter output by the log type of each entry. The log-type column displays when a Layer 3 entry is created, modified, saved, or deleted.

caller init|config|status|switch-cb|cluster|gre|ARP|router|flow-cb|    vdp|vlag|port|inject|evict|vxlan|stats|vnm-vnic|adjacency|stp| trunk|intsw|ttl1|flood|flush|retire|loop|dhcp|fabric|table| l3-age-out|vlan|l2-checker|igmp|l2-age-out|port-mirror|    mac-move|cluster-status|
cluster-status-delete|vxlan-routing|
subnet

Specifies the feature that made the change for this entry.

last-caller init|config|status|switch-cb|
cluster|gre|ARP|router| flow-cb|vdp|vlag|port|inject
|evict|vxlan|stats|vnm-vnic| adjacency|stp|trunk|intsw|ttl1|flood|flush|retire|loop|dhcp|fabric|table|l3-age-out|vlan|l2-checker|igmp|l2-age-out|port-mirror|mac-move|cluster-status|
cluster-status-delete|vxlan-routing|
subnet

Specifies the most recent caller for this entry.

reason activate|deactivate|port-move|ip-move|ip-remove|
batch-move|retire|break-loop|break-loop-timeout|create|modify|
delete| policy|owner-status|
remove-node|port-flags|
check-owner| trunk-port-add|
trunk-port-remove|move-router-if|age-out|hw-remove|restart|undo|flush|update-vxlan-vlan| needs-peer-status|owner-lost|
owner-change

Specifies the reason for history entry.

last-reason activate|deactivate|
port-move|ip-move|ip-remove| batch-move|retire|break-loop|
break-loop-timeout|create|modify| delete|policy|owner-status|
remove-node|port-flags|check-owner|    trunk-port-add|
trunk-port-remove|move-router-if|age-out| hw-remove|restart|undo|
flush|update-vxlan-vlan|    needs-peer-status|owner-lost|owner-change|update-peer-only| user-delete|done|vm-metadata

Specifies the most recent reason for this entry.

changes owner|mac|vnet|public-vlan|ip|num-ips|config-intf|intf|ports|    state|local-intf|local-ports|local-state|alt-owner| alt-owner-port|alt-owner-ports|alt-owner-state|svc-name| hostname|entity|power|cpus|os|portgroup|pg-vlans|vswitch| vs-type|vnic-type|config|rem-switch|rem-intf|rem-ports| peer-intf|peer-state|peer-owner-state|status|tunnel|create-time|last-seen|vxlan-lru|hit|migrate|drops|hw-index|rt-if|
hw-flags

Specifies what changed in this entry.

count count-number

Filter output by the number of entries summed using the sum-by argument.

owner node name

Filter output by the owner.

mac mac-address

Filter output by MAC address.

vnet vnet-name

Filter output by the VNET name.

l2-net l2-net-name

Filter output by the Layer 2 network name.

vlan vlan-id 

Filter output by the VLAN ID.

public-vlan vlan-id

Filter output by the public VLAN ID.

vxlan vxlan-id

Filter output by the VXLAN ID.

ip ip-address 

Filter output by the IP address.

num-ips num-ips-number

Specify the number of IP addresses for the Layer 3 entry.

config-intf config-intf-number

Filter output by the configured interface of the Layer 3 entry.

intf intf-number

Filter output by the interface number. This is the port or trunk number of the Layer 3 entry.

ports port-list

Filter output by the list of ports.

state active|static|vrrp|
tunnel|software|
needs-peer-status|
port-mac|hit|ageout-check|moving|loop-probe|local-tunnel|igmp-mac|    user-flush|vxlan-loopback|router|update-peer-only|active-state-mismatch|peer-port-missing|peer-port-not-vlag| peer-port-not-orphaned|peer-port-not-cluster-link|sw-active| hsrp

Filter output by the state of the Layer 3 entry.

svc-name svc-name-string

Filter output by service name.

hostname hostname-string

Filter output by the host name.

entity entity-string

Filter output by the VM or VM Kernel device name.

power none|powered-off|powered-on|standby|
suspended|unknown

Filter by the vPort power status.

portgroup portgroup-string

Filter by the port group.

pg-vlans vlan-list

Filter by port group VLANs.

vswitch vswitch-string

Filter output by vSwitch name associated with VM MAC address.

vs-type none|host-vs|distributed-vs|unknown

Filter output by vSwitch type.

vnic-type untagged|tagged|trunked|vm-mgmt|vm-kernel|vMotion|vSAN|FTL|    rep|p-NFC|r-NFC|mgmt|unknown

Filter output by VNIC type.

memory memory-number

Filter output by the amount of memory assigned to the VM.

cpus cpus-number

Filter output by the number of CPUs assigned to the VM.

disk disk-number

Filter output by the disk number where the VM is installed.

os os-string

Filter output by the OS installed on the VM.

config none|owner|ip|port|hostname|
hypervisor|vm-id|vm-name| vm-flavor|memory|cpus|disk|os

Filter output by the configuration of the VM.

blocked-port port-list

Filter output by a list of ports to block for the VM.

rem-switch node name

Filter output by the remote switch name.

rem-intf rem-intf-number 

Filter output by the remote interface number.

rem-ports port-list

Filter output by the remote ports.

peer-intf peer-intf-number

Filter output by the vPort peer interface.

peer-state active|static|vrrp|tunnel|software|needs-peer-status|port-mac|hit|ageout-check|moving|loop-probe|local-tunnel|igmp-mac|user-flush|vxlan-loopback|router|pdate-peer-only|active-state-mismatch|peer-port-missing|peer-port-not-vlag| peer-port-not-orphaned|peer-port-not-cluster-link|sw-active| hsrp

Filter output by the vPort peer state.

peer-owner-state active|static|vrrp|tunnel|software|needs-peer-status|port-mac|hit|ageout-check|moving|loop-probe|local-tunnel|igmp-mac|user-flush|vxlan-loopback|router|pdate-peer-only|active-state-mismatch|peer-port-missing|peer-port-not-vlag| peer-port-not-orphaned|peer-port-not-cluster-link|sw-active| hsrp

Filter output by the vPort peer owner state.

status phy-up|up|disabled|hw-nat-loop|mirror-loop|mirror-to|inuse| PN-switch|PN-fabric|PN-other|PN-cluster|PN-internal| PN-hypervisor|PN-guest|snmp-host|host|uplink|drop-pkts| no-pktin|no-fwd|no-flood|STP-BPDUs|LLDP|trunk|l3-port| remote-l3-port|vdp|dhcp|dhcpsvr|blocked|no-BPDU|LACP-PDUs|   vlag-active|vlag-blocked|stp-edge-port|LACP-wait|LACP-fallback|
adjacency-wait|adjacency-check|
vlag-wait|multicast-router|
host-disabled|loop|vxlan-loopback|vlan-up|vle|vle-wait|phy-down|down| enabled|err-disabled|err-bpdu-guard|
mac-violation| stp-bpdu-guard|stp-root-guard

Filter output by the status of the Layer 3 entry.

vtep-ip ip-address

Specifies the IP address of the remote VTEP.

tunnel tunnel-string

Filter output by the tunnel name.

create-time date/time: yyyy-mm-ddTHH:mm:ss

Filter output by the time that the Layer 3 entry was created.

last-seen date/time: yyyy-mm-ddTHH:mm:ss

Filter output by the time that the Layer 3 entry was last seen on the fabric.

vxlan-lru date/time: yyyy-mm-ddTHH:mm:ss

Filter output by the number of received hits.

hit hit-number

Filter output by the number of times that the Layer 3 entry migrated on the fabric.

migrate migrate-number

Filter output by the number of drops on the fabric.

drops drops-number

Filter output by the time that the Layer 3 entry was created.

hw-index hw-index-number

Filter output by the hardware index number.

rt-if rt-if-string

Filter output by the router interface.

hw-flags invalid-vlan|invalid-port

Filter output by hardware flags.

 

Defaults   None

Access   CLI

History   

Version 2.3.2

Command introduced.

Version 2.4

The parameters, l2-checker|igmp|l2-age-out|port-mirror|mac-move added. The parameters, peer-, hw-index, and rt-if added.

Version 2.4.1

The parameters, vnet, public-vlan, and hw-flags added. The options, user-flush|vxlan-loopback|router, added to state, peer-state, and peer-owner-state. The option, cluster-status, added to caller and last-caller. The options, update-vxlan-vlan| needs-peer-status|owner-lost|owner-change added to reason and last-reason.

Version 2.6.2

The parameters, ip, num-ip, svc-name, entity, power, portgroup, pg-vlans, vswitch, vs-type, vnic-type, and hw-flags added. The parameters, hypervisor, vm-id, vm-name, vm-flavor, vm-status, memory, and blocked-port, deprecated.

Version 3.1.0

The parameter, vtep-ip, added.

Usage   Use this command to display history of Layer 3 entries.

Examples  To display Layer 2 information, use the following command:

CLI network-admin@switch > l3-history-show

time:                       09:02:33

log-type:                   l3-modify

caller:                     ARP

reason:                     activate,create

owner:                      pleaides24

mac:                        66:0e:94:f4:ec:6e

vlan:                       1

ip:                         192.168.16.24

state:                      active