port-lacp-show

This command displays information about network LACP port status.

Syntax   port-lacp-show [port port-list] [neighbor|no-neighbor] [name name-string] [port-type none|vlag|trunk] [mode off|passive|active] timeout slow|fast [system-id mac-address] [aggregatable yes|no] [sync yes|no] [coll yes|no] [dist yes|no] [defaulted yes|no] [expired yes|no] [port-state port-state-number] [test-mode none|no-tx|no-rx|no-rx-or-tx]

port port-list

Specifies the switch network data port number, list of ports, or range of ports. Port numbers must be in the range of 1 to 64.

neighbor|no-neighbor

Specify to display neighbors of the LACP port.

name name-string

Specifies the name of the LACP port.

port-type none|vlag|trunk

Specifies if the port is a VLAG or a trunk.

mode off|passive|active

Specifies the mode as off, passive, or active.

timeout slow|fast

Specifies the timeout for LACP connections. Slow timeout sends requests after 30 seconds and fast timeout sends requests after 3 seconds.

system-id mac-address

Specifies the MAC address as the system ID.

lacp-key lacp-key-number

Specifies the LACP key.

system-priority system-priority-number

Specifies the system priority.

port-priority port-priority-number 

Specifies the port priority.

aggregatable yes|no

Specifies if you can aggregate the port or not.

sync yes|no

Specifies if the port is synchronized.

coll yes|no

Specifies if the port is collecting packets or not.

dist yes|no

Specifies if the port is distributing packets or not.

defaulted yes|no

Specifies if the port is defaulted or not.

expired yes|no

Specifies if the port is expired or not.

port-state port-state-number

Specifies a single port state instead of all ports.

test-mode none|no-tx|no-rx|
no-rx-or-tx

Specifies if a port is in test mode.

Formatting Options

format fields-to-display

Display output using a specific parameter. Use all to display all possible output.

parsable-delim character

Display output formatted for machine parsing using a specified delimiter.

sort-asc

Display output in ascending order.

sort-desc

Display output in descending order.

show dups

Display duplicate entries in the output.

layout vertical|horizontal

Format the output in a vertical or horizontal layout.

show-interval seconds-interval

Repeat the show command at a specified interval.

show-headers|
no-show-headers

Display column headers or not.

limit-output number

Limit the display output to a specific number of entries.

count-output

Display the number of entries in the output. This is useful with vRouter show commands.

unscaled

Display full values in the output instead of scaled approximate values.

raw-int-values

Display integer values instead of mapped values

sum-by

Aggregate output by specific parameters. If sum-by fields are specified, records that have the same value in sum-by fields are combined and displayed as one aggregate record. NOTE: This option is only available for show commands that collect statistics such as connection-stats-show.

Defaults   None

Access   CLI

History   Command introduced in nvOS Version 1.2.1.

Version 1.2.1

Command introduced.

Version 2.6.2

The parameters, lacp-key, system-priority, and port-priority added.

Usage   Use this command to display information about port status on the switch.

Examples  To display the port status for port 12, use the following command:

switch:          leo-ext-32

port:            22

name:            t2

port-type:       trunk

mode:            active

timeout:         slow

system-id:       06:c0:00:16:f0:00

lacp-key:        32879

system-priority: 32768

port-priority:   32768

aggregatable:    no

sync:            no

coll:            no

dist:            no

defaulted:       no

expired:         yes

 

See Also   

port-config-modify

port-config-show

port-phy-show

port-stats-clear

port-stats-show

port-vlan-add

port-vlan-remove

port-vlan-show