trunk-modify

This command modifies a trunk for link aggregation on a switch.

Syntax   trunk-modify

name name-string

Specify the name for the trunk configuration.

trunk-id id-number

Specify the trunk ID.

Specify any of the following options:

port port-list

Specify the port number(s) for the link(s) to aggregate into the trunk.

speed disable|100m|1g|10g|40g

Specify the port speed or disable the port.

egress-rate-limit unlimited

Specify an egress rate limit for the configuration.

autoneg|no-autoneg

Specify if you want the physical port to autonegotiate port speed.

jumbo|no-jumbo

Specify if the port can receive jumbo frames.

lacp-mode off|passive|active

Specify the Link Aggregation Control Protocol (LACP) mode for the configuration.

lacp-priority number

Specify the LACP priority. This is a number between 1 and 65535.

lacp-timeout slow|fast

Specify the LACP time out as slow (30 seconds) or fast (4 seconds).

reflect|noreflect

Specify physical port reflection

edge-switch|
no-edge-switch

Specify if the switch is an edge switch.

pause|no-pause

Specify if pause frames are sent.

description description-string

Specify a description for the trunk configuration.

loopback|no-loopback

Specify loopback if you want to use loopback.

vxlan-termination|
no-vxlan-termination

Specify if a VXLAN can terminate on the trunk.

unknown-ucast-level unknown-ucast-level-string

Specify an unknown unicast level in percent. The default value is 100%.

unknown-mcast-level unknown-mcast-level-string

Specify an unknown multicast level in percent. The default value is 100%.

broadcast-level broadcast-level-string

Specify a broadcast level in percent. The default value is 100%.

rem-rswitch-port-mac mac-address

Specify a remote physical port MAC address.

unknown-ucast-level unknown-ucast-level-string

Specify an unknown unicast level in percent. The default value is 100%.

unknown-mcast-level unknown-mcast-level-string

Specify an unknown multicast level in percent. The default value is 100%.

broadcast-level broadcast-level-string

Specify a broadcast level in percent. The default value is 100%.

port-mac-address mac-address

Specify the MAC address of the port.

rem-rswitch-port-mac mac-address

Specify a remote physical port MAC address.

send-port send-port-number

Specify the port to send traffic.

loop-vlans vlan-list

Specify a list of VLANS for looping.

routing|no-routing

Specify if the port participates in routing on the network.

host-enable|host-disable

Enable or disable host facing ports.

dscp-map dscp-map name|none

Specify the DSCP map name to enable on a port

local-switching|no-local-
switching

Specify local-switching or no-local-switching. A no-local-switching port cannot bridge traffic to another no-local-switching port

allowed-tpid q-in-q|q-in-q-old

Specify an allowed TPID in addition to 0x8100 for VLAN headers.

fabric-guard|no-fabric-guard

Specify if fabric guard is enabled.

fec|no-fec

Specify Port Forwarding Error Correction (FEC) mode.

 

Defaults   None

Access   CLI

History   

Version 1.2

Command introduced.

Version 1.2.6

The optional parameter, lacp-mode, was added.

Version 2.1

The parameter id is deprecated. The parameters, enable | disable, lacp-priority, lacp-timeout, reflect, edge-switch, pause, description, loopback, mirror-receive, port-mac, and send-port added.

Version 2.2.5

The parameters, unknown-ucast-level, unknown-mcast-level, and broadcast-level added.

Version 2.2.6

The parameter, egress-rate-limit, added.

Version 2.3

The parameters, auto-neg, eth-mode, and reflect deprecated.The parameter, rem-rswitch-port and routing, added.

Version 2.4

The parameter, enable|disable, deprecated. The parameters, loop-vlans and host-enable, added.

Version 2.5.3

The parameters, reflect|noreflect, dscp-map dscp-map name|none, and local-switching|no-local-switching, added.

Version 2.6.2

The parameter, vxlan-termination, allowed-tpid, and fabric-guard, added. The parameter, mirror-receive-only, deprecated.

Version 3.0.0

The parameter, autoneg|no-autoneg, added.

Version 3.1.0

The parameter, fec|no-fec, added.

Usage   Trunks can be used to aggregate network links at Layer 2 on the local switch. Use this command to modify the links for a trunk.

Examples  To modify a trunk with the name trunk-476, and to aggregate the links connected to ports 11, 21, and 31.

CLI network-admin@switch > trunk-modify name trunk-476 port 11,21,31

See Also   

trunk-create

trunk-delete

trunk-show