trunk-show

This command displays the list of links aggregated into a trunk.

Syntax   trunk-show

intf intf-number

Specifies the interface number.

name name-string

Specifies the name for the trunk configuration.

port port-list

Specifies the port number(s) for the link(s) to aggregate into the trunk.

speed disable|100m|1g|10g|40g

Specifies the port speed or disable the port.

egress-rate-limit unlimited

Specifies if an egress rate limit is configured.

autoneg|no-autoneg

Specifies if the physical port autonegotiates port speed.

eth-mode 1000base-x|sgmii|disabled|1000base-kx|2500base-x|6Gbase-kr| 6Gbase-cr|10Gbase-kr|10Gbase-cr|10Gbase-sr|AN-73|Xaui| 10Gbase-kx4|10Gbase-cx4|24Gbase-kr4|24Gbase-cr4|40Gbase-kr4| XLaui|40Gbase-cr4|40Gbase-sr4|no-phy-present|
MII|GMII|TBI| 10G-XGMII|1G-RGMII|
10G-SFI|10G-XFI

Specifies the Ethernet mode for the trunk.

auto-neg|no-autoneg

Specifies if the port auto negotiates network traffic or does not.

 

jumbo|no-jumbo

Specifies if the port can receive jumbo frames.

enable|disable

Specifies if the physical port is enabled or disabled.

lacp-mode off|passive|active

Specifies the Link Aggregation Control Protocol (LACP) mode for the configuration.

lacp-priority number

Specifies the LACP priority. This is a number between 1 and 65535.

lacp-timeout slow|fast

Specifies the LACP time out as slow (30 seconds) or fast (4 seconds).

lacp-timeout slow|fast

Specify the LACP time out as slow (30 seconds) or fast (4 seconds). The default value is slow.

lacp-fallback bundle|individual

Specify the LACP fallback mode as individual or bundled.

lacp-fallback-timeout seconds

Specify the LACP fallback timeout in seconds. The range is between 30 and 60 seconds with a default value of 50 seconds.

reflect|no-reflect

Specify physical port reflection

edge-switch|
no-edge-switch

Specifies if the switch is an edge switch.

pause|no-pause

Specifies if pause frames are sent.

vxlan-termination|
no-vxlan-termination

Specify if a VXLAN can terminate on the trunk.

unknown-ucast-level unknown-ucast-level-string

Specify an unknown unicast level in percent. The default value is 100%.

unknown-mcast-level unknown-mcast-level-string

Specify an unknown multicast level in percent. The default value is 100%.

broadcast-level broadcast-level-string

Specify a broadcast level in percent. The default value is 100%.

rem-rswitch-port-mac mac-address

Specify a remote physical port MAC address.

description description-string

Specifies a description for the trunk configuration.

loopback|no-loopback

Specifies loopback if you want to use loopback.

vlag vlag-name

Specifies the name of a VLAG.

trunk-hw-id trunk-hw-id-number

Specifies the trunk hardware ID.

send-port send-port-number

Specifies the port to send traffic.

loop-vlans vlan-list

Specify a list of VLANS for looping.

routing|no-routing

Specifies if the port participates in routing on the network.

host-enable|host-disable

Enable or disable host facing ports.

dscp-map dscp-map name|none

Specify the DSCP map name to enable on a port

local-switching|no-local-
switching

Specify local-switching or no-local-switching. A no-local-switching port cannot bridge traffic to another no-local-switching port

allowed-tpid q-in-q|q-in-q-old

Specify an allowed TPID in addition to 0x8100 for VLAN headers.

fabric-guard|no-fabric-guard

Specify if fabric guard is enabled.

fec|no-fec

Specify Port Forwarding Error Correction (FEC) mode.

 

Formatting Options

format fields-to-display

Display output using a specific parameter. Use all to display all possible output.

parsable-delim character

Display output formatted for machine parsing using a specified delimiter.

sort-asc

Display output in ascending order.

sort-desc

Display output in descending order.

show dups

Display duplicate entries in the output.

layout vertical|horizontal

Format the output in a vertical or horizontal layout.

show-interval seconds-interval

Repeat the show command at a specified interval.

show-headers|
no-show-headers

Display column headers or not.

limit-output number

Limit the display output to a specific number of entries.

count-output

Display the number of entries in the output. This is useful with vRouter show commands.

unscaled

Display full values in the output instead of scaled approximate values.

raw-int-values

Display integer values instead of mapped values

sum-by

Aggregate output by specific parameters. If sum-by fields are specified, records that have the same value in sum-by fields are combined and displayed as one aggregate record. NOTE: This option is only available for show commands that collect statistics such as connection-stats-show.

Defaults   None.

Access   CLI

History   

Version 1.2

Command introduced.

Version 1.2.6

The optional parameter, lacp-mode, was added.

Version 2.1

The parameter id is deprecated. The parameters, intf, enable | disable, lacp-priority, lacp-timeout, reflect, edge-switch, pause, description, loopback, mirror-receive, port-mac, and send-port added.

Version 2.2.5

The parameters, unknown-ucast-level, unknown-mcast-level, and broadcast-level added.

Version 2.2.6

The parameter, egress-rate-limit, added.

Version 2.3

The parameters, auto-neg, eth-mode, and reflect deprecated.The parameter, rem-rswitch-port and routing, added.

Version 2.4

The parameters, loop-vlans and host-enable, added. The parameters, unknown-ucast-level, unknown-mcast-level, broadcast-level, and rem-rswitch-port-mac deprecated.

Version 2.5.3

The parameter, reflect|no-reflect, added.

Version 2.6.2

The parameter, vxlan-termination, allowed-tpid, and fabric-guard, added. The parameter, mirror-receive-only, deprecated.

Version 3.0.0

The parameter, autoneg|no-autoneg, added.

Version 3.1.0

The parameter, fec|no-fec, added.

Usage   Trunks can be used to aggregate network links at Layer 2 on the local switch. Use this command to modify the links for a trunk.

Examples  To display a list of all trunks and the aggregated links, use the following command:

CLI network-admin@switch > trunk-show

switch:               pubdev01

intf:                 128

name:                 trunk-top

port:                 26,47-48

speed:                10g

autoneg:              off

jumbo:                off

enable:               off

lacp-mode:            off

lacp-priority:        32768

lacp-timeout:         slow

reflect:              off

edge-switch:          no

pause:                no

description:          

loopback:             off

mirror-only:          off

unknown-ucast-level:  100%

unknown-mcast-level:  100%

broadcast-level:      100%

lport:                0

rswitch-default-vlan: 0

port-mac-address:     06:a0:00:03:00:80

status:               up,PN-switch,PN-fabric,PN-cluster

config:               fd

send-port:            26

 

See Also   

trunk-create

trunk-delete

trunk-modify