This command displays current VLAG configurations on the fabric.

Syntax   vlag-show


id vlag-id

Specifies the VLAG identifier.

name name-string

Specifies the name of the VLAG.


Specifies the name of the cluster.

mode active-standby|

Specifies the mode for the VLAG. Active-standby indicates one side is active and the other is in standby mode. Active-Active indicates that both sides of the VLAG are up by default.


Specifies the behavior in the event of a failover.


Specifies the status of the VLAG.

local-state enabled|up|coming-up

Specifies the local state of the VLAG.

peer-state enabled|up|coming-up

Specifies the peer state of the VLAG.

lacp-mode off|passive|active

Specifies the LACP mode.

lacp-timeout slow|fast

Specifies the LACP timeout.

lacp-key lacp-key-number

Specifies the generated LACP key.

lacp-system-id lacp-system-id-number

Specifies the LACP system ID.

lacp-fallback bundle|individual

Specifies the LACP fallback mode as bundle or individual.

lacp-fallback-timeout seconds

Specifies the LACP fallback timeout between 30 and 60 seconds. The default value is 50 seconds.

lacp-individual port-list

Specifies the LACP ports operating individually.

lacp-port-priority number

Specify the LACP port priority as a value between 1 and 65535.

Formatting Options

format fields-to-display

Display output using a specific parameter. Use all to display all possible output.

parsable-delim character

Display output formatted for machine parsing using a specified delimiter.


Display output in ascending order.


Display output in descending order.

show dups

Display duplicate entries in the output.

layout vertical|horizontal

Format the output in a vertical or horizontal layout.

show-interval seconds-interval

Repeat the show command at a specified interval.


Display column headers or not.

limit-output number

Limit the display output to a specific number of entries.


Display the number of entries in the output. This is useful with vRouter show commands.


Display full values in the output instead of scaled approximate values.


Display integer values instead of mapped values


Aggregate output by specific parameters. If sum-by fields are specified, records that have the same value in sum-by fields are combined and displayed as one aggregate record. NOTE: This option is only available for show commands that collect statistics such as connection-stats-show.

Defaults   None.

Access   CLI


Version 1.2

Command introduced.

Version 2.1

The parameters, cluster, failover, comm-ports, and LACP added.

Version 2.2

The parameters for mode as active-standby and active-active added. Local-port changed to port. The parameter local-state added, and peer-comm-ports deprecated.

Version 2.4

The parameters, lacp-mode,lacp-fallback, and lacp-fallback-timeout, added.

Version 2.5

The parameter, lacp-port-priority, added.

Version 3.1.0

The parameter, peer-state, added.

Usage   A virtual link aggregation group (VLAG) allows links that are physically connected to two different Pluribus Networks devices to appear as a single trunk to a third device. The third device can be a switch, server, or any Ethernet device. A VLAG can provide Layer 2 multi-pathing, which allows you to create redundancy by increasing bandwidth, enabling multiple parallel paths between nodes and load-balancing traffic where alternative paths exist. This command deletes a VLAG.

Examples  To display all VLAGs, use the following command:

CLI network-admin@switch > vlag-show format all layout vertical

id:               a000030:0

name:             fh2

cluster:          pubdev

mode:             active-active

switch:           pubdev01

port:             55

peer-switch:      pubdev02

peer-port:        55

failover-move-L2: no

status:           normal

local-state:      enabled

lacp-mode:        off

lacp-timeout:     slow

lacp-key:         13811

lacp-system-id:   110013777969294

See Also