This command is used to display routing protocol information on a vRouter.

Syntax   vrouter-interface-config-show


vrouter-name name-string

Specifies the vRouter name to add the interface.

Specify the following interface configuration arguments:

nic vrouter-interface-nic

Specifies the NIC to add to the interface.

ospf-hello-interval number

Specifies the OSPF hello interval with a number between 1 and 65535. This configures the interval between sending OSPF hello messages on an interface.

ospf-retransmit-interval seconds

Specify the OSPF retransmit interval from 3 to 65535 seconds. The default is 5 seconds. (IPv4 orIPv6)

ospf-dead-interval number

Specifies the OSPF dead interval with a number between 2 and 65535. This configures the interval in which the vRouter must receive an OSPF hello message before the state of the neighbor changes to down.

ospf-priority number

Specifies the OSPF priority with a number between 0 and 255. A vRouter with a priority of 0 does not participate in the designated router decision. The default value is 1.

ospf-auth-key ospf-auth-key-string

Specifies an authorization key string for the vRouter interface.

ospf-cost number

Specify the OSPF cost with a value between 0 and 655365.

ospf-msg-digest-id id

Specify a value between 1 and 255. If you specify 0, then OSPF MD5 authentication is not set.

ospf-msg-digest-key ospf-msg-digest-

Specify a string for the OSPF message digest key.


Specify if the OSPF interface is passive or not.


Specify if the OSPF interface is passive or not.

ospf-network-type default|point-to-point

Specify the type of OSPF network.

ospf-bfd default|enable|disable

Specify if BFD protocol support for OSPF fault detection is enabled.

bfd-interval interval

Specify the desired BFD transmit interval from 200 ms to 3000 ms. The default value is 750 ms. 200 ms to 3000 ms. The default value is 500 ms

bfd-min-rx interval

Specify the required BFD receive interval from 200 milliseconds to 3000 milliseconds. The default value is 750 milliseconds.

bfd-multiplier integer

Specify the BFD detection multiplier from 1 to 20. The default value is 3.


Specify if you want to suppress the transmit of IPv6 router advertisements.

v6-ra-prefix ip-address

Specify the IPv6 prefix to include in router advertisements.

prefix-netmask netmask 

Specify the IPv6 prefix netmask.


Specify if you want the prefix used for IPv6 autoconfiguration.

ra-interval seconds

Specify the interval between router advertisements in seconds with a range of 1 to 1800 seconds.

ra-lifetime seconds 

Specify the time that the vRouter is considered as the default router.

Formatting Options

format fields-to-display

Display output using a specific parameter. Use all to display all possible output.

parsable-delim character

Display output formatted for machine parsing using a specified delimiter.


Display output in ascending order.


Display output in descending order.

show dups

Display duplicate entries in the output.

layout vertical|horizontal

Format the output in a vertical or horizontal layout.

show-interval seconds-interval

Repeat the show command at a specified interval.


Display column headers or not.

limit-output number

Limit the display output to a specific number of entries.


Display the number of entries in the output. This is useful with vRouter show commands.


Display full values in the output instead of scaled approximate values.


Display integer values instead of mapped values


Aggregate output by specific parameters. If sum-by fields are specified, records that have the same value in sum-by fields are combined and displayed as one aggregate record. NOTE: This option is only available for show commands that collect statistics such as connection-stats-show.

Defaults   None

Access   CLI


Version 2.1

Command introduced.

Version 2.2

The parameter, ospf-cost, added.

Version 2.2.2

The parameters, ospf-msg-digest-key, and ospf-msg-digest-id, added.

Version 2.2.3

The parameters ospf-passive-if and no-ospf-passive-if added.

Version 2.2.6

The parameters, bfd-interval, bfd-min-rx, and bfd-multiplier, added.

Version 2.4.1

The parameter, ospf-network-type, added.

Version 2.5

The parameters, nd-suppress-ra, v6-ra-prefix, prefix-netmask, autoconf|no-autoconf, ra-interval, and ra-lifetime added.

Version 2.5.3

The parameter, ospf-bfd default|enable|disable added.

Version 3.0.0

The parameters, ospf-retransmit-interval,ra-prefix, ra-interval added.

Usage   You can display additional routing information for a vRouter configuration.

Examples  To display the interface, use the following command:

CLI network-admin@switch > vrouter-interface-config-show

See Also