vrouter-interface-show

This command is used to display the interfaces on the virtual router (vRouter) service on a fabric, cluster, standalone switch, or virtual network (VNET).

Syntax   vrouter-interface-show

vrouter-name name-string

Displays the name for the vRouter interface.

Specify the following interface arguments:

nic nic-string

Displays the type of NIC.

ip ip-address

Displays the IP address of the interface.

netmask netmask

Displays the netmask.

assignment none|dhcp|dhcpv6

Displays the DHCP method.

ip2 ip-address

Specify the IP address of the interface.

netmask2 netmask

Specify the netmask.

assignment none|dhcp|dhcpv6|autov6

Specify the DHCP method for IP address assignment. Note that if you specify hardware as the router type, you cannot assign IP addresses using DHCP. You must specify a static IP address.

linklocal ip-address

Displays the link local IPv6 address

vnet vnet-name

Displays the VNET assigned to the vRouter.

mac mac-address

Displays the MAC address assigned to the interface.

vlan-type public|private

Displays the type of VLAN for the interface.

vlan vlan-id

Displays the VLAN identifier. This is a value between 1 and 4094.

if mgmt|data|span

Displays if the interface is a management, data or span interface.

alias-on alias-on-string

Displays an alias for the interface.

vm-nic-type e1000|virtio

Displays the type of VM NIC.

exclusive|
no-exclusive

Displays if the interface is exclusive to the configuration. Exclusive means that other configurations cannot use the interface.

nic-enable|
nic-disable

Displays if the NIC is enabled or disabled.

pim|no-pim

Specify if the vRouter interface is a PIM interface.

pim-dr-priority integer

Specify the direct router (DR) priority as an integer between 1 and 4294967295. Netvisor selects the vRouter interface with higher DR priority as the designated router.

By default, all interfaces are priority 1. In case of same priority, Netvisor selects the vRouter interface with highest network address as DR.

pim-cluster|no-pim-cluster

Specify if you want to provide alternative routing for Layer 3 attached sources for leaf cluster routing configuration. It allows for traffic to failover not black-hole when unicast path to the Spine fails.

nic-state down|up

Displays the NIC state as up or down. If the NIC is disabled, the state is down.

is-primary true|false

Displays the primary VRRP interface.

is-vip true|false

Displays the VIP VRRP interface.

fabric-nic|no-fabric-nic

Specify if VNIC is on a VLAN used for fabric setup.

vrrp-id id-number

Displays the ID for the VRRP interface.

vrrp-primary string

Displays the primary interface for VRRP failover.

vrrp-priority number

Displays the priority for the VRRP interface. This is a value between 1 (lowest) and 255 (highest).

vrrp-adv-int mseconds

Displays a VRRP advertisement interval in milliseconds. The range is from 30 to 40950 with a default value of 1000.

vrrp-state slave|master

Displays the VRRP state as slave or master.

l3-port l3port-usable-port name

Displays a Layer 3 port for the interface.

secondary-macs secondary-macs-string

Displays a secondary MAC address for the interface.

mtu bytes

Displays a MTU value in bytes between 68 and 9216.

sriov-vf|no-sriov-vf

Displays the SRIOV interface vNIC.

mirror-traffic true|false

Displays if the traffic is mirrored from the physical NIC traffic to a vNIC.

if-nat-realm internal|external

Displays a NAT realm for the interface.

priority-tag|
no-priority-tag

Specify if you want to add a VLAN 0 priority tag on forwarded traffic.

Defaults   None.

Access   CLI

History   

Version 1.2

Command introduced.

Version 2.1

The parameters, exclusive, nic and nic-state, added.

Version 2.2

The parameters vrrp-id, vrrp-priority, and vrrp-primary added.

Version 2.2.5

The parameters, l3-port, and secondary-macs, added.

Version 2.3

The parameter, vrrp-adv-int, added.

Version 2.4

The parameter, vrrp-state, added.

Version 2.4.1

The parameter, vlan-type, added.

Version 2.5

The parameter, mtu, added.

Version 2.6.0

The parameter, if-nat-realm internal|external, added.

Version 2.6.2

The parameter, vxlan, deprecated.

Version 3.0.0

The parameter, ip2 and netmask2 added. The parameters, pim, pim-dr-priority, and pim-cluster, added. The parameter, linklocal, added. The option, autov6, deprecated for the parameter, assignment.

Version 3.1.0

The parameter, fabric-nic and priority-tag, added.

Usage   You can display information about the interfaces on the vRouter service on a fabric, cluster, standalone switch, or virtual network (VNET).

Examples  To display information about all interfaces on vRouter services, use the following command:

CLI network-admin@switch > vrouter-interface-show interface layout

See Also   

vrouter-create

vrouter-delete

vrouter-migrate

vrouter-modify

vrouter-show

vrouter-bgp-add

vrouter-bgp-remove

vrouter-bgp-show

vrouter-igmp-static-join-add

vrouter-igmp-static-join-remove

vrouter-igmp-static-join-show

vrouter-interface-add

vrouter-interface-modify

vrouter-interface-remove

vrouter-ospf-add

vrouter-ospf-remove

vrouter-ospf-show

vrouter-ospf-neighbor-show

vrouter-rip-add

vrouter-rip-remove

vrouter-rip-show

vrouter-static-route-add

vrouter-static-route-remove

vrouter-static-route-show