Configuring Layer 3 Features > Configuring Open Shortest Path First (OSPF) > Display Default Timers for OSPF Configurations
Was this helpful?
Display Default Timers for OSPF Configurations
Netvisor ONE allows you to display default timers for OSPF configurations. To add a timer or modify an existing timer, use the following commands:
CLI network-admin@Leaf1 > vrouter-interface-config-add
ospf-retransmit-interval seconds
Specify the OSPF retransmit interval from 3 to 65535 seconds. The default is 5 seconds. (IPv4 orIPv6)
CLI network-admin@Leaf1 > vrouter-interface-config-modify
ospf-retransmit-interval seconds
Specify the OSPF retransmit interval from 3 to 65535 seconds. The default is 5 seconds. (IPv4 orIPv6)
A new command displays the OSPF configuration for an interface:
CLI network-admin@Leaf1 > vrouter-ospf-interface-show
vrouter-name name-string
Displays the name of the vRouter.
Specify any of the following optional OSPF parameters:
nic vrouter interface nic
Displays the name of the vNIC.
nic-state down|up
Displays the vNIC state.
l3-port l3-port-number
Displays the Layer 3 port numbers.
ip ip-address
Displays the IPv4 address of the interface.
netmask netmask
Displays the netmask of the IPv6 address.
broadcast ip-address
Displays the broadcast IP address.
area ip-address
Displays the area ID for the interface in IPv4 format.
mtu mtu-number
Displays MTU for the interface.
mtu-mismatch-detection|
no-mtu-mismatch-detection
Displays if MTU mismatch detection is configured.
router-id ip-address
Displays the router ID as an IP address.
network-type point-to-point|broadcast|loopback
Displays the OSPF network type.
state down|loopback|waiting|point-to-point|dr-other|backup|dr
Displays OSPF interface state.
dr-id ip-address
Displays the designated router ID.
dr-ip ip-address
Displays the designated router IP address.
bdr-id ip-address
Displays the backup designated router ID.
bdr-ip ip-address
Displays the designated router IP address.
priority priority-number
Displays the priority.
cost cost-number
Displays the cost.
hello hello-number(s)
Displays the hello-interval in seconds.
dead dead-number(s)
Displays the dead time in seconds.
retransmit retransmit-number(s)
Displays the retransmit interval time in seconds.
hello-due hello-due-string
Displays the hello due in.
neighbor neighbor-number
Displays the neighbor count.
adjacent adjacent-number
Displays the adjacent number count.
CLI network-admin@Leaf1 > vrouter-ospf6-interface-show
vrouter-name name-string
Displays the name of the vRouter.
Specify any of the following optional OSPF parameters:
nic vrouter interface nic
Displays the name of the vNIC.
nic-state down|up
Displays the vNIC state.
l3-port l3-port-number
Displays the Layer 3 port numbers.
link-local ip-address
Displays the IPv6 link-local IP address.
ip6 ip-address
Displays the IPv6 address of the interface.
netmask-ip6 netmask
Displays the netmask of the IP address.
area ip-address
Displays the area ID for the interface in IPv4 format.
mtu mtu-number
Displays MTU for the interface.
mtu-mismatch-detection|
no-mtu-mismatch-detection
Displays if MTU mismatch detection is configured.
state down|loopback|waiting|point-to-
point|dr-other|backup|dr
Displays OSPF interface state.
dr-id ip-address
Displays the designated router ID.
bdr-id ip-address
Displays the backup designated router ID.
priority priority-number
Displays the priority.
cost cost-number
Displays the cost.
hello hello-number(s)
Displays the hello-interval in seconds.
dead dead-number(s)
Displays the dead time in seconds.
retransmit retransmit-number(s)
Displays the retransmit interval time in seconds.
if-scoped-lsa if-scoped-lsa-number
Displays the number of interface LSAs scoped for the area.
ls-update ls-update-number
Displays the number of pending LSAs for LSUpdate.
ls-ack ls-ack-number
Displays the number of pending LSAs for LSAck.