vrouter-create

This command creates a new virtual router (vRouter) service for a fabric, cluster, or standalone switch.

Syntax   vrouter-create

name name-string

Specify the name of the vRouter.

vnet vnet-name

Specify the name of the VNET.

router-type

hardware|software

Specify if the vrouter uses hardware or software. Note that if you specify hardware as the router type, you cannot assign IP addresses using DHCP. You must specify a static IP address.

Any of the following options:

shared-vnet-mgr vnet-manager name

Specifies the VNET manager to share with if this is a shared service

disable|enable

Specify to enable or disable the vRouter service.

location fabric-node name

Specify the location of the service.

storage-pool storage-pool-name

Specify the storage pool.

router-ipstack quagga|frr

Specify the vRouter IP stack.

cluster-active-active-routing|no-cluster-active-active-routing   

Specify active-active routing with or without VRRP.

hw-vrrp-id hw-vrrp-id-number

Specifies the VRRP ID for a hardware router.

bgp-as bgp-as-number

Specify the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP).

router-id ip-address

Specify the vRouter IP address

proto-multi none|pim-ssm

Specify the optional multicast protocol for the vRouter service. Select none, Vector Multicast Routing Protocol (VMRP), or Protocol Independent Multicast-source specific mode (PIM-SIM).

bgp-redistribute static|connected|rip|ospf

Specify how BGP routes are redistributed.

bgp-redist-static-metric none

Specify a static metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset.

bgp-redist-connected-metric none

Specify a connected metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset.

bgp-redist-rip-metric none

Specify a RIP metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset.

bgp-redist-ospf-metric none

Specify a OSPF metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset.

bgp-cluster-id ip-address

Specify an IP address for a BGP cluster.

bgp-max-paths bgp-max-paths-number

Specify the maximum number of paths for BGP. This is a number between 1 and 255 or 0 to unset.

bgp-ibgp-multipath bgp-ibgp-multipath-number

Specify the number of multipaths for BGP. This is a number between 1 and 255 or 0 to unset.

bgp-bestpath-as-path none|ignore

Specify a parameter for a best path as path.

bgp-dampening|
no-bgp-dampening

Specify a BGP damp

bgp-graceful-restart|
no-bgp-graceful-restart

Specify a graceful restart for BGP routing. The default is graceful restart.

bgp-stalepath-time second

Specify the length of time befor a BGP path becomes stale. This is a value between 0 and 3600 or 0 to unset.

bgp-scantime seconds

Specify a BGP scanner interval in seconds. The default interval is 60 seconds with a range of 5 to 60 seconds.

bgp-delayed-startup seconds

Specify a time in seconds to delay forming peer adjacency on bootup.

bgp-keepalive-interval seconds

Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds.

bgp-holdtime seconds

Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds.

bgp-distance-external integer

Specify the BGP distance for routes external to the AS.

bgp-distance-internal integer

Specify the BGP distance for routes internal to the AS.

bgp-distance-local integer

Specify the BGP distance for routes local to the AS.

bgp-ipv4-unicast|no-bgp-ipv4-
unicast

Specify a MP-BGP Control default IPv4 Unicast AFI/SAFI.

rip-redistribute static|connected|ospf|
bgp

Specify how RIP routes are redistributed.

vrrp-track-port port-list

Specify a port to track a VRRP configuration.

ospf-redistribute static|connected|rip|
bgp

Specify how OSPF routes are redistributed.

ospf-redist-static-metric-type 1|2

Specify a static metric type for OSPF route redistribution. This is a number between 0 and 16777214 or 'none' to unset.

ospf-redist-connected-metric none

Specify a connected metric for OSPF route redistribution.

ospf-redist-connected-metric-type 1|2

Specify a connected metric type for OSPF route redistribution.

ospf-stub-router-on-startup|
no-ospf-stub-router-on-startup

Specify if you want advertise self as stub router temporary on startup.

ospf-stub-router-on-startup-period integer

Specify the time period to advertise self as stub router on startup. This s a value between 5 and 86400 seconds.

ospf-redist-rip-metric none

Specify a RIP metric type for OSPF route redistribution. This is a number between 0 and 16777214 or 'none' to unset.

ospf-redist-rip-metric-type 1|2

Specify a RIP metric type for OSPF route redistribution.

ospf-redist-bgp-metric none

Specify a BGP metric type for OSPF route redistribution. This is a number between 0 and 16777214 or 'none' to unset.

ospf-redist-bgp-metric-type 1|2

Specify a BGP metric type for OSPF route redistribution.

ospf6-redistribute static|connected|bgp4

Specify if you want to redistribute OSPF6 routes.

ospf-distance-external integer

Specify the OSPF distance for routes external to the AS.

ospf-distance-internal integer

Specify the OSPF distance for routes internal to the AS.

ospf-distance-local integer

Specify the OSPF distance for routes local to the AS.

ospf-stub-router-on-startup|
no-ospf-stub-router-on-startup

Specify if you want the OSPF router to act as a stub router at startup.

ospf-stub-router-on-startup-
period seconds

Specify the time period for the OSPF stub router in seconds. You can configure from 5 to 86400 seconds.

ospf-bfd-all-if|
no-ospf-bfd-all-if

Specify if you want to use BFD protocol for fault detection on all OSPF interfaces.

ospf-default-information none|originate|always

Specify if you want to control origination of default route.

ospf-default-info-originate-
metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-metric-type 1|2

Specify the metric type for OSPF origination of default route.

ospf6-redist-static-metric none

Specify a metric for OSPF6 redistribute of static routes.

ospf6-redist-static-metric-
type 1|2

Specify a metric type for OSPF6 redistribution of static routes.

ospf6-redist-connected-metric none

Specify a metric for OSPF6 redistribution of connected routes.

ospf6-redist-connected-metric-type 1|2

Specify a metric type for OSPF6 redistribution.

ospf-default-information none|originate|always

Specify how to control the origination of default route.

ospf-default-info-originate-
metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-
metric-type 1|2

Specify the metric type for OSPF origination of default route.

ospf-default-info-originate-route-map vrouter route-map name   

Specify the route map for OSPF origination of default route.

vrrp-track-port port-listS

Specify the ports for VRRP tracking.

bgp-snmp|no-bgp-snmp

Enable or disable BGP SNMP MIB.

bgp-snmp-notification|no-bgp-
snmp-notification

Enable or disable SNMP notifications for BGP MIBs.

ospf-snmp|no-ospf-snmp

Enable or disable OSPF SNMP MIB.

ospf-snmp-notification|no-ospf-snmp-notification

Enable or disable SNMP notifications for OSPF MIBs.

ospf6-snmp|no-ospf6-snmp

Enable or disable OSPFv3 SNMP MIB.

ospf6-snmp-notification|no-bgp-snmp-notification

Enable or disable SNMP notifications for OSPFv3 MIBs.

ip-snmp|no-ip-snmp

Enable or disable ipForward SNMP MIBs.

no-bgp-redist-static-route-map

Remove route map for BGP static redistribution.

no-bgp-redist-connected-route-map

Remove route map for BGP connected redistribution.

no-bgp-redist-ospf-route-map

Remove route map for BGP OSPF redistribution.

bgp-graceful-shutdown|no-bgp-graceful-shutdown

Specify BGP graceful shutdown according to RFE 8326.

Defaults   None.

Access   CLI

History   

Version 1.2

Command introduced.

Version 2.0

Parameter router-type added.

Version 2.2

The parameter, hw-vrrp-id, added. The parameters, bgp-redistribute, rip-redistribute, and ospf-redistribute, added.

Version 2.2.3

The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added.

Version 2.3.1

The parameters, ospf6-, added.

Version 2.4

The parameters, ospf-stub-router-on-startup and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added.

Version 2.4.1

The parameter, bgp-distance-, and ospf-distance, added.

Version 2.5.4

The parameter, shared-vnet-mgr, added.

Version 2.6.0

SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added.

Version 3.0.0

The parameters, ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added.

Version 3.1.0

The parameters for route maps added.

Usage   Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command creates a new vRouter service.

Examples  To create a vRouter, MyvService, for the VNET, net-ops, as a shared service, with the IP address of 208.74.182.1, use the following command:

CLI network-admin@switch > vrouter-create name MyvService vnet net-ops shared-vnet-services router-id 208.74.182.1

vrouter-delete

This command deletes a virtual router (vRouter) service for a fabric, cluster, or standalone switch.

Syntax   vrouter-delete

name name-string

Specify the name of the vRouter service.

Defaults   None.

Access   CLI

History   Command introduced in nvOS Version 1.2.1.

Usage   Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command deletes a vRouter service.

Examples  To delete the vRouter service, MyvService, use the following command:

CLI network-admin@switch > vrouter-delete name MyvService

vrouter-migrate

The command migrates a vRouter service.

Syntax   vrouter-migrate name name-string location fabric-node-name storage-pool storage-pool-name

name name-string

Specify the name of the vRouter.

Between one or two of the following options:

location fabric-node-name

Specify the location name.

storage-pool storage-pool-name

Specify the storage pool name.

Defaults   None.

Access   CLI.

History   Command introduced in nvOS Version 1.2.1.

Usage   Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command migrates a vRouter service.

Examples  To migrate the vRouter service, MyvService, on fabric, pn-fabric, to the storage pool, keep-all, use the following command:

CLI network-admin@switch > vrouter-migrate name MyvService location pn-fabric storage-pool keep-all

vrouter-modify

This command modifies a virtual router (vRouter) services for a fabric, cluster, or standalone switch.

Syntax   vrouter-modify

name name-string

Specify the name of the vRouter.

Any of the following options:

disable|enable

Specify to enable or disable the vRouter service.

gateway ip-address

Specify the IP address of the gateway.

storage-pool storage-pool-name

Specify the storage pool.

cluster-active-active-routing|
no-cluster-active-active-routing

Specify if you want active-active routing with or without VRRP.

hw-vrrp-id hw-vrrp-id-number

Specify the VRRP ID assigned to the hardware vRouter.

bgp-as bgp-as-number

Specify the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP).

router-id ip-address

Specify the vRouter IP address

proto-multi none|pim-ssm

Specify the optional multicast protocol for the vRouter service. Select none or Protocol Independent Multicast-source specific mode (PIM-SSM). 

bgp-redistribute static|connected|rip|ospf

Specify how BGP routes are redistributed.

bgp-redist-static-metric none

Specify a static metric for BGP route redistribution.

bgp-redist-static-route-map vrouter route-map name

Specify the route map for BGP redistribution of static routes.

bgp-redist-connected-metric none

Specify a connected metric for BGP route redistribution

bgp-redist-connected-route-map vrouter route-map name

Specify the route map for BGP redistribution of connected routes.

bgp-redist-rip-metric none

Specify a RIP metric for BGP route redistribution.

bgp-redist-ospf-metric none

Specify a OSPF metric for BGP route redistribution.

bgp-redist-ospf-route-map vrouter route-map name

Specify the route map for BGP redistribution of OSPF routes.

bgp-cluster-id ip-address

Specify an IP address for a BGP cluster.

bgp-max-paths bgp-max-paths-number

Specify the maximum number of paths for BGP.

bgp-ibgp-multipath bgp-ibgp-multipath-number

Specify the number of multipaths for BGP.

bgp-bestpath-as-path none|ignore

Specify a parameter for a best path as path.

bgp-dampening|no-bgp-dampening

Specify a BGP damp

bgp-graceful-restart|
no-bgp-graceful-restart

Specify a graceful restart for BGP routing.

bgp-stalepath-time second

Specify the length of time befor a BGP path becomes stale. This is a value between 0 and 3600.

bgp-scantime seconds

Specify a BGP scanner interval in seconds. The default interval is 60 seconds with a range of 5 to 60 seconds.

bgp-delayed-startup seconds

Specify if you want to delay forming peer adjacency when switch is starting. This is a value between 5 and 36000 seconds.

bgp-keepalive-interval seconds

Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds.

bgp-holdtime seconds

Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds.

bgp-distance-external integer

Specify the BGP distance for routes external to the AS.

bgp-distance-internal integer

Specify the BGP distance for routes internal to the AS.

bgp-distance-local integer

Specify the BGP distance for routes local to the AS.

rip-redistribute static|connected|ospf|bgp

Specify how RIP routes are redistributed.

ospf-redistribute static|connected|rip|bgp

Specify how OSPF routes are redistributed.

vrrp-track-port port-list

Specify a port to track a VRRP configuration.

ospf-redist-static-metric none

Specify a static route metric type for OSPF route redistribution.

ospf-redist-static-metric-
type 1|2

Specify a static route metric type for OSPF route redistribution.

ospf-redist-static-route-map vrouter route-map name

Specify the route map for OSPF redistribution of static routes.

ospf-redist-connected-metric none

Specify a connected metric type for OSPF route redistribution.

ospf-redist-connected-metric-
type 1|2

Specify a connected metric type for OSPF route redistribution.

ospf-redist-connected-route-map vrouter route-map name

Specify the route map for OSPF redistribution of connected routes.

ospf-redist-rip-metric none

Specify a RIP metric type for OSPF route redistribution.

ospf-redist-rip-metric-type 1|2

Specify a RIP metric type for OSPF route redistribution.

ospf-redist-bgp-metric none

Specify a BGP metric type for OSPF route redistribution.

ospf-redist-bgp-metric-type 1|2

Specify a BGP metric type for OSPF route redistribution.

ospf-redist-bgp-route-map vrouter route-map name

Specify the route map for OSPF redistribution of BGP routes.

ospf6-redistribute static|connected|bgp4

Specify if you want to redistribute OSPF6 routes.

ospf6-redist-static-metric none

Specify a metric for OSPF6 redistribute of static routes.

ospf6-redist-static-metric-
type 1|2

Specify a metric type for OSPF6 redistribution of static routes.

ospf-distance-external integer

Specify the OSPF distance for routes external to the AS.

ospf-distance-internal integer

Specify the OSPF distance for routes internal to the AS.

ospf-distance-local integer

Specify the OSPF distance for routes local to the AS.

ospf-stub-router-on-startup|
no-ospf-stub-router-on-startup

Specify if you want advertise self as stub router temporary on startup.

ospf-stub-router-on-startup-period integer

Specify the time period to advertise self as stub router on startup. This s a value between 5 and 86400 seconds.

ospf-bfd-all-if|
no-ospf-bfd-all-if

Specify if you want to use BFD protocol for fault detection on all OSPF interfaces.

ospf-default-information none|originate|always

Specify if you want to control origination of default route.

ospf-default-info-originate-
metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-metric-type 1|2

Specify the metric type for OSPF origination of default route.

ospf6-redist-connected-metric none

Specify a metric for OSPF6 redistribution of connected routes.

ospf6-redist-connected-metric-

type 1|2

Specify a metric type for OSPF6 redistribution.

ospf-bfd-all-if|no-ospf-bfd-
all-if

Enables or disables BFD protocol for fault detection on all (global) OSPF interfaces. Default is disabled.

ospf-default-information none|originate|always

Specify how to control the origination of default route.

ospf-default-info-originate-
metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-
metric-type 1|2

Specify the metric type for OSPF origination of default route.

ospf-default-info-originate-route-map vrouter route-map name   

Specify the route map for OSPF origination of default route.

vrrp-track-port port-list

Specify the ports to track for VRRP.

bgp-snmp|no-bgp-snmp

Enable or disable BGP SNMP MIB.

bgp-snmp-notification|no-bgp-snmp-notification

Enable or disable SNMP notifications for BGP MIBs.

ospf-snmp|no-ospf-snmp

Enable or disable OSPF SNMP MIB.

ospf-snmp-notification|no-ospf-snmp-notification

Enable or disable SNMP notifications for OSPF MIBs.

ospf6-snmp|no-ospf6-snmp

Enable or disable OSPFv3 SNMP MIB.

ospf6-snmp-notification|no-bgp-snmp-notification

Enable or disable SNMP notifications for OSPFv3 MIBs.

ip-snmp|no-ip-snmp

Enable or disable ipForward SNMP MIBs.

no-bgp-redist-static-route-map

Remove route map for BGP static redistribution.

no-bgp-redist-connected-route-map

Remove route map for BGP connected redistribution.

no-bgp-redist-ospf-route-map

Remove route map for BGP OSPF redistribution.

Defaults   None.

Access   CLI

History   

Version 1.2

Command introduced.

Version 2.0

Parameter router-type added.

Version 2.1

The parameter, storage-pool, deprecated. The parameter, gateway, added.

Version 2.2

The parameter, router-type, is deprecated.

Version 2.2

The parameters, bgp-redistribute, rip-redistribute, and ospf-redistribute, added.

Version 2.2.3

The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added.

Version 2.3.1

The parameters, ospf6-, added.

Version 2.4

The parameters, ospf-stub-router-on-startup and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added.

Version 2.4.1

The parameter, bgp-distance-, and ospf-distance, added.

Version 2.5.3

The parameter ospf-bfd-all-if|no-ospf-bfd-all-if added.

Version 2.6

SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added.

Version 2.6.2

The parameter, cluster-active-active-routing and bgp-delayed-startup, added.

Version 3.0.0

The parameters, ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added.

Version 3.1.0

The parameters for route maps added.

Usage   Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command modifies a vRouter service.

Examples  To modify a vRouter, MyvService, for the VNET, net-ops, as a shared service, and disable it, use the following command:

CLI network-admin@switch > vrouter-modify name MyvService vnet net-ops shared-vnet-services disable

vrouter-show

This command displays a virtual router (vRouter) service for a fabric, cluster, or standalone switch.

Syntax   vrouter-show

id

The ID number assigned to the configuration.

name name-string

Specifies the name of the vRouter.

type vnet-mgr|vrouter|vlb|
dhcp|dns|netzone| ofpd|orphaned|netvm|

nat|openstack|netvmm

Specifies the type of vRouter.

scope local|fabric

Specifies the scope of the vRouter.

vnet vnet-name

Specifies the name of the VNET.

location fabric-node-name

Specifies the location of the vRouter on the fabric.

router-type hardware|software

Specifies the router type as hardware or software.

hw-router-mac mac-address

Specifies the MAC address of the hardware router.

fabric-comm

Specifies if Netvisor uses the vRouter as a fabric communication interface.

router-ipstack quagga|frr

Specifies the type of vRouter IP stack.

hw-vrid hw-vrid-number

Specifies the virtual router ID of the hardware router.

hw-vrrp-id hw-vrrp-id-number

Specifies the VRRP ID for a hardware router.

bgp-as bgp-as-number

Specifies the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP).

router-id ip-address

Specifies the vRouter IP address

proto-multi none|vmrp|pim-ssm

Specifies the optional multicast protocol for the vRouter service. Select none, Vector Multicast Routing Protocol (VMRP), or Protocol Independent Multicast-source specific mode (PIM-SIM).

bgp-redistribute static|connected|rip|ospf

Specify how BGP routes are redistributed.

bgp-redist-static-metric none

Specify a static metric for BGP route redistribution.

bgp-redist-connected-metric none

Specify a connected metric for BGP route redistribution

bgp-redist-rip-metric none

Specify a RIP metric for BGP route redistribution.

bgp-redist-ospf-metric none

Specify a OSPF metric for BGP route redistribution.

bgp-cluster-id ip-address

Specify an IP address for a BGP cluster.

bgp-max-paths bgp-max-paths-number

Specify the maximum number of paths for BGP.

bgp-ibgp-multipath bgp-ibgp-multipath-number

Specify the number of multipaths for BGP.

bgp-bestpath-as-path none|ignore

Specify a parameter for a best path as path.

bgp-dampening|
no-bgp-dampening

Specify a BGP damp

bgp-graceful-restart|
no-bgp-graceful-restart

Specify a graceful restart for BGP routing.

bgp-stalepath-time second

Specify the length of time befor a BGP path becomes stale. This is a value between 0 and 3600.

bgp-scantime seconds

Specify a BGP scanner interval in seconds. The default interval is 60 seconds with a range of 5 to 60 seconds.

bgp-keepalive-interval seconds

Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds.

bgp-holdtime seconds

Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds.

bgp-distance-external integer

Specify the BGP distance for routes external to the AS.

bgp-distance-internal integer

Specify the BGP distance for routes internal to the AS.

bgp-distance-local integer

Specify the BGP distance for routes local to the AS.

bgp-ipv4-unicast|
no-bgp-ipv4-unicast

Specify a MP-BGP Control default IPv4 Unicast AFI/SAFI.

rip-redistribute static|connected|ospf|
bgp

Specify how RIP routes are redistributed.

ospf-redistribute static|connected|rip|
bgp

Specify how OSPF routes are redistributed.

vrrp-track-port port-list

Specify a port to track a VRRP configuration.

ospf-redist-static-
metric-type 1|2

Specify a static metric type for OSPF route redistribution.

ospf-distance-external integer

Specify the OSPF distance for routes external to the AS.

ospf-distance-internal integer

Specify the OSPF distance for routes internal to the AS.

ospf-distance-local integer

Specify the OSPF distance for routes local to the AS.

ospf-stub-router-on-startup|
no-ospf-stub-router-on-startup

Specify if you want advertise self as stub router temporarily on startup.

ospf-stub-router-on-startup-period integer

Specify the time period to advertise self as stub router on startup. This s a value between 5 and 86400 seconds.

ospf-bfd-all-if|
no-ospf-bfd-all-if

Specify if you want to use BFD protocol for fault detection on all OSPF interfaces.

ospf-default-information none|originate|always

Specify if you want to control origination of default route.

ospf-default-info-originate-
metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-metric-type 1|2

Specify the metric type for OSPF origination of default route.

ospf-redist-connected-
metric none

Specify a connected metric type for OSPF route redistribution.

ospf-redist-connected-
metric-
type 1|2

Specify a connected metric type for OSPF route redistribution.

ospf-redist-rip-metric none

Specify a RIP metric type for OSPF route redistribution.

ospf-redist-rip-metric-type 1|2

Specify a RIP metric type for OSPF route redistribution.

ospf-redist-bgp-metric none

Specify a BGP metric type for OSPF route redistribution.

ospf-redist-bgp-metric-type 1|2

Specify a BGP metric type for OSPF route redistribution.

ospf6-redistribute static|connected|bgp4

Specify if you want to redistribute OSPF6 routes.

ospf6-redist-static-metric none

Specify a metric for OSPF6 redistribute of static routes.

ospf6-redist-static-metric-
type 1|2

Specify a metric type for OSPF6 redistribution of static routes.

ospf6-redist-connected-metric none

Specify a metric for OSPF6 redistribution of connected routes.

ospf6-redist-connected-metric-type 1|2

Specify a metric type for OSPF6 redistribution.

ospf-default-information none|originate|always

Specify how to control the origination of default route.

ospf-default-info-originate-metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-metric-
type 1|2

Specify the metric type for OSPF origination of default route.

ospf-default-info-originate-route-
map vrouter route-map name   

Specify the route map for OSPF origination of default route.

bgp-snmp|no-bgp-snmp

Enable or disable BGP SNMP MIB.

bgp-snmp-notification|no-bgp-snmp-notification

Enable or disable SNMP notifications for BGP MIBs.

ospf-snmp|no-ospf-snmp

Enable or disable OSPF SNMP MIB.

ospf-snmp-notification|no-ospf-snmp-notification

Enable or disable SNMP notifications for OSPF MIBs.

ospf6-snmp|no-ospf6-snmp

Enable or disable OSPFv3 SNMP MIB.

ospf6-snmp-notification|no-bgp-snmp-notification

Enable or disable SNMP notifications for OSPFv3 MIBs.

ip-snmp|no-ip-snmp

Enable or disable ipForward SNMP MIBs.

no-bgp-redist-static-route-map

Remove route map for BGP static redistribution.

no-bgp-redist-connected-route-map

Remove route map for BGP connected redistribution.

no-bgp-redist-ospf-route-map

Remove route map for BGP OSPF redistribution.

Defaults   None.

Access   CLI

History   

Version 1.2

Command introduced.

Version 2.0

Parameter type added.

Version 2.2

The parameter, location, hw-router-mac, and hw-vrrp-id, added. The parameters, bgp-redistribute, rip-redistribute, and ospf-redistribute, added.

Version 2.2.3

The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added

Version 2.3.1

The parameters, ospf6-, added.

Version 2.4

The parameters, ospf-stub-router-on-startup and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added.

Version 2.4.1

The parameter, bgp-distance-, and ospf-distance-, added.

Version 2.5.4

The parameter, shared-vnet-mgr, added.

Version 2.6

SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added.

Version 3.0.0

The parameters, ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added.

Version 3.1.0

The parameters for route maps added.

Usage   Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command displays vRouter service.

Examples  To display all vRouter services, use the following command:

CLI (network-admin@techpubs-aquila1) > vrouter-show format all layout vertical

id:                 a0000dd:7

name:               vrrp-rtr1

type:               vrouter

scope:              fabric

vnet:               vrrp-router

vnet-service:       shared

state:              enabled

location:           techpubs-aquila1

storage-pool:       rpool

template:           no

router-type:        software

proto-multi:        none

id:                 6000021:c

name:               vrrp-rfr2

type:               vrouter

scope:              fabric

vnet:               vrrp-router

vnet-service:       dedicated

state:              enabled

location:           techpubs-aquila2

storage-pool:       rpool

template:           no

router-type:        software

proto-multi:        none