vrouter-create
This command creates a new virtual router (vRouter) service for a fabric, cluster, or standalone switch.
Syntax vrouter-create
name name-string |
Specify the name of the vRouter. |
vnet vnet-name |
Specify the name of the VNET. |
router-type hardware|software |
Specify if the vrouter uses hardware or software. Note that if you specify hardware as the router type, you cannot assign IP addresses using DHCP. You must specify a static IP address. |
Any of the following options: |
|
shared-vnet-mgr vnet-manager name |
Specifies the VNET manager to share with if this is a shared service |
disable|enable |
Specify to enable or disable the vRouter service. |
location fabric-node name |
Specify the location of the service. |
storage-pool storage-pool-name |
Specify the storage pool. |
router-ipstack quagga|frr |
Specify the vRouter IP stack. |
cluster-active-active-routing|no-cluster-active-active-routing |
Specify active-active routing with or without VRRP. |
hw-vrrp-id hw-vrrp-id-number |
Specifies the VRRP ID for a hardware router. |
bgp-as bgp-as-number |
Specify the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP). |
router-id ip-address |
Specify the vRouter IP address |
proto-multi none|pim-ssm |
Specify the optional multicast protocol for the vRouter service. Select none, Vector Multicast Routing Protocol (VMRP), or Protocol Independent Multicast-source specific mode (PIM-SIM). |
bgp-redistribute static|connected|rip|ospf |
Specify how BGP routes are redistributed. |
bgp-redist-static-metric none |
Specify a static metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset. |
bgp-redist-connected-metric none |
Specify a connected metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset. |
bgp-redist-rip-metric none |
Specify a RIP metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset. |
bgp-redist-ospf-metric none |
Specify a OSPF metric for BGP route redistribution. This is a number between 0 and 4294967295 or specify none to unset. |
bgp-cluster-id ip-address |
Specify an IP address for a BGP cluster. |
bgp-max-paths bgp-max-paths-number |
Specify the maximum number of paths for BGP. This is a number between 1 and 255 or 0 to unset. |
bgp-ibgp-multipath bgp-ibgp-multipath-number |
Specify the number of multipaths for BGP. This is a number between 1 and 255 or 0 to unset. |
bgp-bestpath-as-path none|ignore |
Specify a parameter for a best path as path. |
bgp-dampening| |
Specify a BGP damp |
bgp-graceful-shutdown| |
Specify a graceful shutdown for BGP routing (RFC8326). |
bgp-stalepath-time second |
Specify the length of time befor a BGP path becomes stale. This is a value between 0 and 3600 or 0 to unset. |
bgp-scantime seconds |
Specify a BGP scanner interval in seconds. The default interval is 60 seconds with a range of 5 to 60 seconds. |
bgp-delayed-startup seconds |
Specify a time in seconds to delay forming peer adjacency on bootup. |
bgp-keepalive-interval seconds |
Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds. |
bgp-holdtime seconds |
Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds. |
bgp-distance-external integer |
Specify the BGP distance for routes external to the AS. |
bgp-distance-internal integer |
Specify the BGP distance for routes internal to the AS. |
bgp-distance-local integer |
Specify the BGP distance for routes local to the AS. |
bgp-ipv4-unicast|no-bgp-ipv4- |
Specify a MP-BGP Control default IPv4 Unicast AFI/SAFI. |
rip-redistribute static|connected|ospf| |
Specify how RIP routes are redistributed. |
vrrp-track-port port-list |
Specify a port to track a VRRP configuration. |
ospf-redistribute static|connected|rip| |
Specify how OSPF routes are redistributed. |
ospf-redist-static-metric-type 1|2 |
Specify a static metric type for OSPF route redistribution. This is a number between 0 and 16777214 or 'none' to unset. |
ospf-redist-connected-metric none |
Specify a connected metric for OSPF route redistribution. |
ospf-redist-connected-metric-type 1|2 |
Specify a connected metric type for OSPF route redistribution. |
ospf-stub-router-on-startup| |
Specify if you want advertise self as stub router temporary on startup. |
ospf-stub-router-on-startup-period integer |
Specify the time period to advertise self as stub router on startup. This s a value between 5 and 86400 seconds. |
ospf-redist-rip-metric none |
Specify a RIP metric type for OSPF route redistribution. This is a number between 0 and 16777214 or 'none' to unset. |
ospf-redist-rip-metric-type 1|2 |
Specify a RIP metric type for OSPF route redistribution. |
ospf-redist-bgp-metric none |
Specify a BGP metric type for OSPF route redistribution. This is a number between 0 and 16777214 or 'none' to unset. |
ospf-redist-bgp-metric-type 1|2 |
Specify a BGP metric type for OSPF route redistribution. |
ospf6-redistribute static|connected|bgp4 |
Specify if you want to redistribute OSPF6 routes. |
ospf-distance-external integer |
Specify the OSPF distance for routes external to the AS. |
ospf-distance-internal integer |
Specify the OSPF distance for routes internal to the AS. |
ospf-distance-local integer |
Specify the OSPF distance for routes local to the AS. |
ospf-stub-router-on-startup| |
Specify if you want the OSPF router to act as a stub router at startup. |
ospf-stub-router-on-startup- |
Specify the time period for the OSPF stub router in seconds. You can configure from 5 to 86400 seconds. |
ospf-bfd-all-if| |
Specify if you want to use BFD protocol for fault detection on all OSPF interfaces. |
ospf-default-information none|originate|always |
Specify if you want to control origination of default route. |
ospf-default-info-originate- |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate-metric-type 1|2 |
Specify the metric type for OSPF origination of default route. |
ospf6-redist-static-metric none |
Specify a metric for OSPF6 redistribute of static routes. |
ospf6-redist-static-metric- |
Specify a metric type for OSPF6 redistribution of static routes. |
ospf6-redist-connected-metric none |
Specify a metric for OSPF6 redistribution of connected routes. |
ospf6-redist-connected-metric-type 1|2 |
Specify a metric type for OSPF6 redistribution. |
ospf-default-information none|originate|always |
Specify how to control the origination of default route. |
ospf-default-info-originate- |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate- |
Specify the metric type for OSPF origination of default route. |
ospf-default-info-originate-route-map vrouter route-map name |
Specify the route map for OSPF origination of default route. |
vrrp-track-port port-listS |
Specify the ports for VRRP tracking. |
bgp-snmp|no-bgp-snmp |
Enable or disable BGP SNMP MIB. |
bgp-snmp-notification|no-bgp- |
Enable or disable SNMP notifications for BGP MIBs. |
ospf-snmp|no-ospf-snmp |
Enable or disable OSPF SNMP MIB. |
ospf-snmp-notification|no-ospf-snmp-notification |
Enable or disable SNMP notifications for OSPF MIBs. |
ospf6-snmp|no-ospf6-snmp |
Enable or disable OSPFv3 SNMP MIB. |
ospf6-snmp-notification|no-bgp-snmp-notification |
Enable or disable SNMP notifications for OSPFv3 MIBs. |
ip-snmp|no-ip-snmp |
Enable or disable ipForward SNMP MIBs. |
no-bgp-redist-static-route-map |
Remove route map for BGP static redistribution. |
no-bgp-redist-connected-route-map |
Remove route map for BGP connected redistribution. |
no-bgp-redist-ospf-route-map |
Remove route map for BGP OSPF redistribution. |
bgp-graceful-shutdown|no-bgp-graceful-shutdown |
Specify BGP graceful shutdown according to RFE 8326. |
Defaults None.
Access CLI
History
Version 1.2 |
Command introduced. |
Version 2.0 |
Parameter router-type added. |
Version 2.2 |
The parameter, hw-vrrp-id, added. The parameters, bgp-redistribute, rip-redistribute, and ospf-redistribute, added. |
Version 2.2.3 |
The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added. |
Version 2.3.1 |
The parameters, ospf6-, added. |
Version 2.4 |
The parameters, ospf-stub-router-on-startup and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added. |
Version 2.4.1 |
The parameter, bgp-distance-, and ospf-distance, added. |
Version 2.5.4 |
The parameter, shared-vnet-mgr, added. |
Version 2.6.0 |
SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added. |
Version 3.0.0 |
The parameters, ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added. |
Version 3.1.0 |
The parameters for route maps added. |
Version 5.1.1 |
The parameter bgp-graceful-shutdown|no-bgp-graceful-shutdown is added. |
Version 5.1.1 |
The parameter bgp-graceful-restart|no-bgp-graceful-restart is removed. |
Usage Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command creates a new vRouter service.
Examples To create a vRouter, MyvService, for the VNET, net-ops, as a shared service, with the IP address of 208.74.182.1, use the following command:
CLI network-admin@switch > vrouter-create name MyvService vnet net-ops shared-vnet-services router-id 208.74.182.1
vrouter-delete
This command deletes a virtual router (vRouter) service for a fabric, cluster, or standalone switch.
Syntax vrouter-delete
name name-string |
Specify the name of the vRouter service. |
Defaults None.
Access CLI
History Command introduced in nvOS Version 1.2.1.
Usage Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command deletes a vRouter service.
Examples To delete the vRouter service, MyvService, use the following command:
CLI network-admin@switch > vrouter-delete name MyvService
vrouter-migrate
The command migrates a vRouter service.
Syntax vrouter-migrate name name-string location fabric-node-name storage-pool storage-pool-name
name name-string |
Specify the name of the vRouter. |
Between one or two of the following options: |
|
location fabric-node-name |
Specify the location name. |
storage-pool storage-pool-name |
Specify the storage pool name. |
Defaults None.
Access CLI.
History Command introduced in nvOS Version 1.2.1.
Usage Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command migrates a vRouter service.
Examples To migrate the vRouter service, MyvService, on fabric, pn-fabric, to the storage pool, keep-all, use the following command:
CLI network-admin@switch > vrouter-migrate name MyvService location pn-fabric storage-pool keep-all
vrouter-modify
This command modifies a virtual router (vRouter) services for a fabric, cluster, or standalone switch.
Syntax vrouter-modify
name name-string |
Specify the name of the vRouter. |
Any of the following options: |
|
disable|enable |
Specify to enable or disable the vRouter service. |
gateway ip-address |
Specify the IP address of the gateway. |
storage-pool storage-pool-name |
Specify the storage pool. |
cluster-active-active-routing| |
Specify if you want active-active routing with or without VRRP. |
hw-vrrp-id hw-vrrp-id-number |
Specify the VRRP ID assigned to the hardware vRouter. |
bgp-as bgp-as-number |
Specify the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP). |
router-id ip-address |
Specify the vRouter IP address |
proto-multi none|pim-ssm |
Specify the optional multicast protocol for the vRouter service. Select none or Protocol Independent Multicast-source specific mode (PIM-SSM). |
bgp-redistribute static|connected|rip|ospf |
Specify how BGP routes are redistributed. |
bgp-redist-static-metric none |
Specify a static metric for BGP route redistribution. |
bgp-redist-static-route-map vrouter route-map name |
Specify the route map for BGP redistribution of static routes. |
bgp-redist-connected-metric none |
Specify a connected metric for BGP route redistribution |
bgp-redist-connected-route-map vrouter route-map name |
Specify the route map for BGP redistribution of connected routes. |
bgp-redist-rip-metric none |
Specify a RIP metric for BGP route redistribution. |
bgp-redist-ospf-metric none |
Specify a OSPF metric for BGP route redistribution. |
bgp-redist-ospf-route-map vrouter route-map name |
Specify the route map for BGP redistribution of OSPF routes. |
bgp-cluster-id ip-address |
Specify an IP address for a BGP cluster. |
bgp-max-paths bgp-max-paths-number |
Specify the maximum number of paths for BGP. |
bgp-ibgp-multipath bgp-ibgp-multipath-number |
Specify the number of multipaths for BGP. |
bgp-bestpath-as-path none|ignore |
Specify a parameter for a best path as path. |
bgp-dampening|no-bgp-dampening |
Specify a BGP damp |
bgp-graceful-restart| |
Specify a graceful restart for BGP routing. |
bgp-stalepath-time second |
Specify the length of time befor a BGP path becomes stale. This is a value between 0 and 3600. |
bgp-scantime seconds |
Specify a BGP scanner interval in seconds. The default interval is 60 seconds with a range of 5 to 60 seconds. |
bgp-delayed-startup seconds |
Specify if you want to delay forming peer adjacency when switch is starting. This is a value between 5 and 36000 seconds. |
bgp-keepalive-interval seconds |
Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds. |
bgp-holdtime seconds |
Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds. |
bgp-distance-external integer |
Specify the BGP distance for routes external to the AS. |
bgp-distance-internal integer |
Specify the BGP distance for routes internal to the AS. |
bgp-distance-local integer |
Specify the BGP distance for routes local to the AS. |
rip-redistribute static|connected|ospf|bgp |
Specify how RIP routes are redistributed. |
ospf-redistribute static|connected|rip|bgp |
Specify how OSPF routes are redistributed. |
vrrp-track-port port-list |
Specify a port to track a VRRP configuration. |
ospf-redist-static-metric none |
Specify a static route metric type for OSPF route redistribution. |
ospf-redist-static-metric- |
Specify a static route metric type for OSPF route redistribution. |
ospf-redist-static-route-map vrouter route-map name |
Specify the route map for OSPF redistribution of static routes. |
ospf-redist-connected-metric none |
Specify a connected metric type for OSPF route redistribution. |
ospf-redist-connected-metric- |
Specify a connected metric type for OSPF route redistribution. |
ospf-redist-connected-route-map vrouter route-map name |
Specify the route map for OSPF redistribution of connected routes. |
ospf-redist-rip-metric none |
Specify a RIP metric type for OSPF route redistribution. |
ospf-redist-rip-metric-type 1|2 |
Specify a RIP metric type for OSPF route redistribution. |
ospf-redist-bgp-metric none |
Specify a BGP metric type for OSPF route redistribution. |
ospf-redist-bgp-metric-type 1|2 |
Specify a BGP metric type for OSPF route redistribution. |
ospf-redist-bgp-route-map vrouter route-map name |
Specify the route map for OSPF redistribution of BGP routes. |
ospf6-redistribute static|connected|bgp4 |
Specify if you want to redistribute OSPF6 routes. |
ospf6-redist-static-metric none |
Specify a metric for OSPF6 redistribute of static routes. |
ospf6-redist-static-metric- |
Specify a metric type for OSPF6 redistribution of static routes. |
ospf-distance-external integer |
Specify the OSPF distance for routes external to the AS. |
ospf-distance-internal integer |
Specify the OSPF distance for routes internal to the AS. |
ospf-distance-local integer |
Specify the OSPF distance for routes local to the AS. |
ospf-stub-router-on-startup| |
Specify if you want advertise self as stub router temporary on startup. |
ospf-stub-router-on-startup-period integer |
Specify the time period to advertise self as stub router on startup. This s a value between 5 and 86400 seconds. |
ospf-bfd-all-if| |
Specify if you want to use BFD protocol for fault detection on all OSPF interfaces. |
ospf-default-information none|originate|always |
Specify if you want to control origination of default route. |
ospf-default-info-originate- |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate-metric-type 1|2 |
Specify the metric type for OSPF origination of default route. |
ospf6-redist-connected-metric none |
Specify a metric for OSPF6 redistribution of connected routes. |
ospf6-redist-connected-metric- type 1|2 |
Specify a metric type for OSPF6 redistribution. |
ospf-bfd-all-if|no-ospf-bfd- |
Enables or disables BFD protocol for fault detection on all (global) OSPF interfaces. Default is disabled. |
ospf-default-information none|originate|always |
Specify how to control the origination of default route. |
ospf-default-info-originate- |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate- |
Specify the metric type for OSPF origination of default route. |
ospf-default-info-originate-route-map vrouter route-map name |
Specify the route map for OSPF origination of default route. |
vrrp-track-port port-list |
Specify the ports to track for VRRP. |
bgp-snmp|no-bgp-snmp |
Enable or disable BGP SNMP MIB. |
bgp-snmp-notification|no-bgp-snmp-notification |
Enable or disable SNMP notifications for BGP MIBs. |
ospf-snmp|no-ospf-snmp |
Enable or disable OSPF SNMP MIB. |
ospf-snmp-notification|no-ospf-snmp-notification |
Enable or disable SNMP notifications for OSPF MIBs. |
ospf6-snmp|no-ospf6-snmp |
Enable or disable OSPFv3 SNMP MIB. |
ospf6-snmp-notification|no-bgp-snmp-notification |
Enable or disable SNMP notifications for OSPFv3 MIBs. |
ip-snmp|no-ip-snmp |
Enable or disable ipForward SNMP MIBs. |
no-bgp-redist-static-route-map |
Remove route map for BGP static redistribution. |
no-bgp-redist-connected-route-map |
Remove route map for BGP connected redistribution. |
no-bgp-redist-ospf-route-map |
Remove route map for BGP OSPF redistribution. |
Defaults None.
Access CLI
History
Version 1.2 |
Command introduced. |
Version 2.0 |
Parameter router-type added. |
Version 2.1 |
The parameter, storage-pool, deprecated. The parameter, gateway, added. |
Version 2.2 |
The parameter, router-type, is deprecated. |
Version 2.2 |
The parameters, bgp-redistribute, rip-redistribute, and ospf-redistribute, added. |
Version 2.2.3 |
The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added. |
Version 2.3.1 |
The parameters, ospf6-, added. |
Version 2.4 |
The parameters, ospf-stub-router-on-startup and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added. |
Version 2.4.1 |
The parameter, bgp-distance-, and ospf-distance, added. |
Version 2.5.3 |
The parameter ospf-bfd-all-if|no-ospf-bfd-all-if added. |
Version 2.6 |
SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added. |
Version 2.6.2 |
The parameter, cluster-active-active-routing and bgp-delayed-startup, added. |
Version 3.0.0 |
The parameters, ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added. |
Version 3.1.0 |
The parameters for route maps added. |
Usage Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command modifies a vRouter service.
Examples To modify a vRouter, MyvService, for the VNET, net-ops, as a shared service, and disable it, use the following command:
CLI network-admin@switch > vrouter-modify name MyvService vnet net-ops shared-vnet-services disable
vrouter-show
This command displays a virtual router (vRouter) service for a fabric, cluster, or standalone switch.
Syntax vrouter-show
id |
The ID number assigned to the configuration. |
name name-string |
Specifies the name of the vRouter. |
type vnet-mgr|vrouter|vlb| nat|openstack|netvmm |
Specifies the type of vRouter. |
scope local|fabric |
Specifies the scope of the vRouter. |
vnet vnet-name |
Specifies the name of the VNET. |
location fabric-node-name |
Specifies the location of the vRouter on the fabric. |
router-type hardware|software |
Specifies the router type as hardware or software. |
hw-router-mac mac-address |
Specifies the MAC address of the hardware router. |
fabric-comm |
Specifies if Netvisor uses the vRouter as a fabric communication interface. |
router-ipstack quagga|frr |
Specifies the type of vRouter IP stack. |
hw-vrid hw-vrid-number |
Specifies the virtual router ID of the hardware router. |
hw-vrrp-id hw-vrrp-id-number |
Specifies the VRRP ID for a hardware router. |
bgp-as bgp-as-number |
Specifies the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP). |
router-id ip-address |
Specifies the vRouter IP address |
proto-multi none|vmrp|pim-ssm |
Specifies the optional multicast protocol for the vRouter service. Select none, Vector Multicast Routing Protocol (VMRP), or Protocol Independent Multicast-source specific mode (PIM-SIM). |
bgp-redistribute static|connected|rip|ospf |
Specify how BGP routes are redistributed. |
bgp-redist-static-metric none |
Specify a static metric for BGP route redistribution. |
bgp-redist-connected-metric none |
Specify a connected metric for BGP route redistribution |
bgp-redist-rip-metric none |
Specify a RIP metric for BGP route redistribution. |
bgp-redist-ospf-metric none |
Specify a OSPF metric for BGP route redistribution. |
bgp-cluster-id ip-address |
Specify an IP address for a BGP cluster. |
bgp-max-paths bgp-max-paths-number |
Specify the maximum number of paths for BGP. |
bgp-ibgp-multipath bgp-ibgp-multipath-number |
Specify the number of multipaths for BGP. |
bgp-bestpath-as-path none|ignore |
Specify a parameter for a best path as path. |
bgp-dampening| |
Specify a BGP damp |
bgp-graceful-restart| |
Specify a graceful restart for BGP routing. |
bgp-stalepath-time second |
Specify the length of time befor a BGP path becomes stale. This is a value between 0 and 3600. |
bgp-scantime seconds |
Specify a BGP scanner interval in seconds. The default interval is 60 seconds with a range of 5 to 60 seconds. |
bgp-keepalive-interval seconds |
Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds. |
bgp-holdtime seconds |
Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds. |
bgp-distance-external integer |
Specify the BGP distance for routes external to the AS. |
bgp-distance-internal integer |
Specify the BGP distance for routes internal to the AS. |
bgp-distance-local integer |
Specify the BGP distance for routes local to the AS. |
bgp-ipv4-unicast| |
Specify a MP-BGP Control default IPv4 Unicast AFI/SAFI. |
rip-redistribute static|connected|ospf| |
Specify how RIP routes are redistributed. |
ospf-redistribute static|connected|rip| |
Specify how OSPF routes are redistributed. |
vrrp-track-port port-list |
Specify a port to track a VRRP configuration. |
ospf-redist-static- |
Specify a static metric type for OSPF route redistribution. |
ospf-distance-external integer |
Specify the OSPF distance for routes external to the AS. |
ospf-distance-internal integer |
Specify the OSPF distance for routes internal to the AS. |
ospf-distance-local integer |
Specify the OSPF distance for routes local to the AS. |
ospf-stub-router-on-startup| |
Specify if you want advertise self as stub router temporarily on startup. |
ospf-stub-router-on-startup-period integer |
Specify the time period to advertise self as stub router on startup. This s a value between 5 and 86400 seconds. |
ospf-bfd-all-if| |
Specify if you want to use BFD protocol for fault detection on all OSPF interfaces. |
ospf-default-information none|originate|always |
Specify if you want to control origination of default route. |
ospf-default-info-originate- |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate-metric-type 1|2 |
Specify the metric type for OSPF origination of default route. |
ospf-redist-connected- |
Specify a connected metric type for OSPF route redistribution. |
ospf-redist-connected- |
Specify a connected metric type for OSPF route redistribution. |
ospf-redist-rip-metric none |
Specify a RIP metric type for OSPF route redistribution. |
ospf-redist-rip-metric-type 1|2 |
Specify a RIP metric type for OSPF route redistribution. |
ospf-redist-bgp-metric none |
Specify a BGP metric type for OSPF route redistribution. |
ospf-redist-bgp-metric-type 1|2 |
Specify a BGP metric type for OSPF route redistribution. |
ospf6-redistribute static|connected|bgp4 |
Specify if you want to redistribute OSPF6 routes. |
ospf6-redist-static-metric none |
Specify a metric for OSPF6 redistribute of static routes. |
ospf6-redist-static-metric- |
Specify a metric type for OSPF6 redistribution of static routes. |
ospf6-redist-connected-metric none |
Specify a metric for OSPF6 redistribution of connected routes. |
ospf6-redist-connected-metric-type 1|2 |
Specify a metric type for OSPF6 redistribution. |
ospf-default-information none|originate|always |
Specify how to control the origination of default route. |
ospf-default-info-originate-metric none |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate-metric- |
Specify the metric type for OSPF origination of default route. |
ospf-default-info-originate-route- |
Specify the route map for OSPF origination of default route. |
bgp-snmp|no-bgp-snmp |
Enable or disable BGP SNMP MIB. |
bgp-snmp-notification|no-bgp-snmp-notification |
Enable or disable SNMP notifications for BGP MIBs. |
ospf-snmp|no-ospf-snmp |
Enable or disable OSPF SNMP MIB. |
ospf-snmp-notification|no-ospf-snmp-notification |
Enable or disable SNMP notifications for OSPF MIBs. |
ospf6-snmp|no-ospf6-snmp |
Enable or disable OSPFv3 SNMP MIB. |
ospf6-snmp-notification|no-bgp-snmp-notification |
Enable or disable SNMP notifications for OSPFv3 MIBs. |
ip-snmp|no-ip-snmp |
Enable or disable ipForward SNMP MIBs. |
no-bgp-redist-static-route-map |
Remove route map for BGP static redistribution. |
no-bgp-redist-connected-route-map |
Remove route map for BGP connected redistribution. |
no-bgp-redist-ospf-route-map |
Remove route map for BGP OSPF redistribution. |
Defaults None.
Access CLI
History
Version 1.2 |
Command introduced. |
Version 2.0 |
Parameter type added. |
Version 2.2 |
The parameter, location, hw-router-mac, and hw-vrrp-id, added. The parameters, bgp-redistribute, rip-redistribute, and ospf-redistribute, added. |
Version 2.2.3 |
The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added |
Version 2.3.1 |
The parameters, ospf6-, added. |
Version 2.4 |
The parameters, ospf-stub-router-on-startup and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added. |
Version 2.4.1 |
The parameter, bgp-distance-, and ospf-distance-, added. |
Version 2.5.4 |
The parameter, shared-vnet-mgr, added. |
Version 2.6 |
SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added. |
Version 3.0.0 |
The parameters, ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added. |
Version 3.1.0 |
The parameters for route maps added. |
Usage Each fabric, cluster, standalone switch, or virtual network (VNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command displays vRouter service.
Examples To display all vRouter services, use the following command:
CLI (network-admin@techpubs-aquila1) > vrouter-show format all layout vertical
id: a0000dd:7
name: vrrp-rtr1
type: vrouter
scope: fabric
vnet: vrrp-router
vnet-service: shared
state: enabled
location: techpubs-aquila1
storage-pool: rpool
template: no
router-type: software
proto-multi: none
id: 6000021:c
name: vrrp-rfr2
type: vrouter
scope: fabric
vnet: vrrp-router
vnet-service: dedicated
state: enabled
location: techpubs-aquila2
storage-pool: rpool
template: no
router-type: software
proto-multi: none