vrouter-mfib-routes-show
This command is used to display multicast routes in forwarding information database.
Syntax vrouter-mfib-routes-show
type <*,G>|<*,G,V> |
Displays the type of hardware router. |
srcip ip-address |
Displays the source IP address. |
srcip-mask netmask |
Displays the source netmask. |
group ip-address |
Displays the group IP address. |
group-mask netmask |
Displays the group netmask. |
vnet vnet-name |
Displays the VNET for the VLAN. |
vlan vlan-id |
Displays the VLAN identifier. |
vrid vrouter-id |
Displays the virtual router identifier. |
hw-group-id hw-group-id |
Displays the hardware group identifier. |
send-vnet vnet-name |
Displays the VNET of the sending VLAN. |
send-vlan vlan-id |
Displays the sending VLAN identifier. |
ports port-list |
Displays the port list. |
encap-id encap-id-number |
Displays the encapsulation identifier. |
flags Trunk|Active |
Displays the hardware flags for the route. |
Defaults None
Access CLI
History .
Version 2.2.5 |
Command introduced. |
Version 2.4.1 |
The parameter, vnet, added. |
Version 2.6.2 |
The parameter, send-vnet, added. |
Usage Use this command to display information about multicast routes in the forwarding information database (FIB).
Examples To display multicast routes in the FIB, use the following syntax:
CLI network-admin@switch > vrouter-mfib-routes-show
switch: pleiades23
type: <S,G,V>
srcip 10.16.110.100
group: 239.2.2.2
vlan: 113
vrid: 0
hw-group-id: 2000006
send-vlan ports: none
encap-id flags: -1
flags: Active
switch: pleiades23
type: <S,G,V>
srcip 10.16.110.100
group: 239.1.1.1
vlan: 113
vrid: 0
hw-group-id: 2000007
send-vlan ports: none
encap-id flags: 0
flags: Active
switch: pleiades23
type: <*,G,V>
srcip 0.0.0.0
group: 239.2.2.2
vlan: 115
vrid: 0
hw-group-id: 2000005
send-vlan ports: none
encap-id flags: 1
flags: Active
vrouter-multicast-igmp-group-show
This command displays the Internet Group Management Protocol (IGMP) group state for each multicast router.
Syntax vrouter-multicast-igmp-group-show
vrouter-name name-string |
Displays the vRouter name. |
if-name if-name-string |
Displays the physical name of the virtual interface. |
address ip-address |
Displays the local IP address. |
vif vif-number |
Displays the virtual interface identifier. |
reporter ip-address |
Displays the reporter IP address. |
timer timer-number |
Displays the timer number. |
Defaults None
Access CLI
History Command introduced in Version 2.2.5.
Usage Use this command to display information about IGMP group state for each multicast router.
Examples To display information about IGMP group state, use the following syntax:
CLI network-admin@switch > vrouter-multicast-igmp-group-show
vrouter-name if-name address reporter
------------ -------- ---------- -------------
vr0 eth0.110 224.0.0.13 10.16.110.1
vr0 eth0.110 224.0.0.2 10.16.110.1
vr0 eth0.110 224.0.0.22 10.16.110.1
vr0 eth0.111 224.0.0.13 10.16.111.1
vr0 eth0.111 224.0.0.2 10.16.111.1
vr0 eth0.111 224.0.0.22 10.16.111.1
vr0 eth0.112 224.0.0.2 10.16.112.1
vr0 eth0.112 224.0.0.22 10.16.112.1
vr0 eth0.110 224.0.0.5 10.16.110.1
vr0 eth0.111 224.0.0.5 10.16.111.1
vr0 eth0.112 224.0.0.5 10.16.112.1
vr0 eth0.112 224.0.0.13 10.16.112.2
vr0 eth0.110 224.0.0.6 10.16.110.1
vr0 eth0.111 224.0.0.6 10.16.111.1
vr0 eth0.112 224.0.0.6 10.16.112.2
vr0 eth0.113 224.0.0.5 10.16.113.1
vr0 eth0.113 224.0.0.13 10.16.113.2
vr0 eth0.113 224.0.0.2 10.16.113.2
vr0 eth0.113 224.0.0.22 10.16.113.1
vr0 eth0.113 224.0.0.6 10.16.113.2
vr1 eth1.112 224.0.0.13 10.16.112.2
vr1 eth1.112 224.0.0.2 10.16.112.2
vr1 eth1.112 224.0.0.22 10.16.112.2
vr1 eth0.114 224.0.0.13 10.16.114.1
vr1 eth0.114 224.0.0.2 10.16.114.1
vr1 eth0.114 224.0.0.22 10.16.114.1
vr1 eth1.112 224.0.0.5 10.16.112.1
vr1 eth0.114 224.0.0.5 10.16.114.1
vr1 eth0.114 224.0.0.6 10.16.114.1
vr1 eth1.112 224.0.0.6 10.16.112.2
vr2 eth1.114 224.0.0.13 10.16.114.2
vr2 eth1.114 224.0.0.2 10.16.114.2
vr2 eth1.114 224.0.0.22 10.16.114.2
vr2 eth0.115 224.0.0.13 10.16.115.1
vr2 eth0.115 224.0.0.2 10.16.115.1
vr2 eth0.115 224.0.0.22 10.16.115.1
vr2 eth1.114 224.0.0.5 10.16.114.2
vr2 eth0.115 224.0.0.5 10.16.115.1
vr2 eth1.114 224.0.0.6 10.16.114.1
vr2 eth0.115 224.0.0.6 10.16.115.1
vr2 eth0.115 224.1.1.1 10.16.115.100
vr2 eth1.113 224.0.0.5 10.16.113.1
vr2 eth1.113 224.0.0.13 10.16.113.2
vr2 eth1.113 224.0.0.2 10.16.113.2
vrouter-multicast-route-show
This command displays the multicast forwarding state for one more multicast routers or one or more multicast groups.
Syntax vrouter-multicast-route-show
vrouter-name name-string |
Displays the vRouter name. |
source ip-address |
Displays the source IP address. |
group ip-address |
Displays the group IP address. |
parent parent-number |
Displays the parent number. |
oif_bitmap oif_bitmap-number |
Displays the bitmap of virtual interfaces to forward packets. |
incoming-if if-string |
Displays the name of the incoming interface. |
outgoing-if if-string |
Displays the name of the outgoing interface. |
Defaults None
Access CLI
History Command introduced in Version 2.2.5.
Usage Use this command to display information about muticast routes.
Examples To display multicast route information use the following syntax:
CLI network-admin@switch > vrouter-multicast-route-show
vrouter-name source group incoming-if outgoing-ifs
------------ ------------- --------- ----------- ------------
vr0 10.16.110.100 224.1.1.1 eth0.110 eth0.112
vr1 10.16.110.100 224.1.1.1 eth1.112 eth0.114
vr2 10.16.110.100 224.1.1.1 eth1.114 eth0.115