Netvisor ONE Command Reference A-Z

intf intf-number

Displays the interface number.

name name-string

If configured, displays the name of the port. Otherwise, the field is blank.

port port-list

Displays a port or list of ports.

speed disable|10m|100m|1g|2.5g|10g|25g|40g|50g|100g

Displays the port speed. Ports configured for speeds of 1G must be equipped with SFP transceivers. Ports configured for 10G or higher must be equipped with SFP+ or QSFP+ transceivers.

egress-rate-limit unlimited

Displays the egress rate limit for the port.

bw-bps bw-bps-number 

Specify the bandwidth bps for the port.

eth-mode [sr4|lr4|cr4|caui4|sr|lr|cr] 

Displays the Ethernet mode.

autoneg|no-autoneg

Displays if the port auto-negotiates the port speed with a peer.

jumbo|no-jumbo

Displays if the port forwards jumbo frames. Jumbo frames are Ethernet frames with more than 1500 bytes of payload.

enable|disable

Displays if the port is enabled and forwards or drops frames.

lacp-priority integer

Displays the LACP priority for the port. This is a value between 1 and 65535 with a default value of 32768.

reflect|no-reflect

Displays if the port reflects frames received for loopback testing.

edge-switch|
no-edge-switch

Displays if the port connects to another Pluribus Networks device or is an uplink to a third-party switch or host.

pause|no-pause

Displays if the port traffic is paused or not.

description description-string

Displays a description for the port.

loopback|no-loopback

Displays to use loopback or no loopback.

vxlan-termination|no-vxlan-termination

Displays if a VXLAN terminates on a port.

mirror-receive-only|no-mirror-receive-only

Displays if you want the port to receive mirrored traffic only.

vle vle name

Displays the VLE on this port.

trunk-hw-id trunk-hw-id-number

DisplaysDisplaysDisplays the trunk hardware ID assigned..

trunk trunk-name

Displays the trunk name for the port.

vlag vlag-name

Displays the VLAG for the port.

send-port send-port-number

Displays the port number to send in packets.

loop-vlans vlan-list

Displays the VLANs that are looping on the network.

routing|no-routing

Displays if the port is participating in routing on the switch.

host-enable|host-disable

Displays if you want host-facing ports enabled or disabled.

crc-check-enable|crc-check-disable

Displays if you want CRC checking performed by the port. This is applicable to a switch in Virtual Wire mode. The default value is crc-check-disable.

defer-bringup|no-defer-bringup

Specify if you want to delay port activation.

dscp-map dscp-map name | none

Displays a DSCP map name to enable on port.

local-switching|no-local-switching

Displays if local switching is allowed on the port.

rhost rhost-string

Displays the physical remote host.

allowed-tpid q-in-q|q-in-q-old

Specify the allowed TPID in addition to 0x8100 on VLAN header

fabric-guard|no-fabric-guard

Displays if you want loop detection enabled on the port.

Version 1.2

Command introduced.

Version 1.2.6

The optional parameters for LACP added.

Version 2.1

The parameters, loopback, mirror-receive, vlag-failover, and send-port added.

Version 2.2.6

The parameter, egress-rate-limit, introduced.

Version 2.3.1

Multiple parameters for LACP added.

Version 2.4

The parameter, host-enable, and loop-vlans added.

Version 2.4.1

The parameters, lacp-fallback, lacp-fallback-timeout and lacp-individual deprecated.

Version 2.5.2

The parameter, crc-check-enable|crc-check-disable, introduced.

Version 2.5.3

The parameters, reflect|no-reflect, vxlan-termination, dscp-map, and local-switching added.

Version 2.6.0

The parameter, fabric-guard, and allowed-tpid, added.

Version 3.0.0

The parameter, bw-bps, added.

Version 5.1.0

The following parameter deprecated:

• bw-bps

The following parameters introduced:

• additional Ethernet modes

• defer-bringup|no-defer-bringup

• fec|no-fec|fec-auto