vport-show

This command is used to display information about virtual ports on a fabric. Virtual ports track switch information across nodes on the fabric.

Informational Note:  Netvisor does not automatically populate the output fields for hypervisor and VM. In future releases, Netvisor gathers this information using a multicast communication across the fabric.

Syntax   vport-show

owner node name 

Displays the owner name.

mac mac-address

Displays the MAC address of the vPort.

vnet vnet-name

Displays the VNET name.

bd bridge-domain name

Bridge Domain assigned to vPort.

vlan vlan-id

Displays a VLAN from 0 to 4095.

inner-vlan 0..4095

Q-in-Q inner VLAN assigned to vPort.

public-vlan 0..4095

Displays the ID of the public VLAN.

vxlan vxlan-id

Displays a VXLAN from 0 to 16777215.

ip ip-address

DisplaysDisplays an IP address.

num-ips num-ips-number

Displays the number of IP addresses for the vPort.

config-intf config-intf-number

Displays the configuration interface number.

intf intf-number

Port that owns the vPort

ports port-list

Displays the list of ports.

state active|static|vrrp|tunnel|software|needs-peer-status|port-mac|hit|ageout-check|moving|loop-probe|local-tunnel|igmp-mac|user-flush|vxlan-loopback|router|update-peer-only|active-state-mismatch|peer-port-missing|peer-port-not-vlag|peer-port-not-orphaned|peer-port-not-cluster-link|sw-active|anycast|hsrp|invalid-vlan|owner-lost|cluster-link-down|vxlan-router|peer-force-resync|excess-mac-move-detected|excess-ip-move-detected|retry|evpn|evpn-wo-bgp|evpn-def-gw|evpn-delete 

Displays the vPort state.

svc-name svc-name-string

Displays the name of the vCenter connection service.

hostname hostname-string

Displays the hypervisor or switch host name.

entity entity-string

Displays the VM or KVM device name.

power none|powered-off|powered-on|standby|suspended|unknown

Displays the vPort entry status.

cpus cpus-number

Displays the number of CPUs assigned to the VM.

os os-string

Displays an operating system, such as CentOS or Ubuntu, on the VM.

portgroup portgroup-string

Displays the port group name associated with the VM MAC address.

pg-vlans vlan-list

Displays the VLANs assigned to a port group.

vswitch vswitch-string

Displays the name of the virtual switch associated with a NIC.

vs-type none|host-vs|distributed-vs|
unknown

Displays the type of virtual switch.

vnic-type untagged|tagged|trunked|vm-mgmt|vm-kernel|vMotion|vSAN|FTL|    rep|p-NFC|r-NFC|mgmt|unknown

Displays the type of vNIC associated with the VM or VM-Kernel.

config none|owner|ip|port|hostname|entity|cpus|os

Displays the configuration type for the virtual switch.

rem-switch node name

Displays the name of the remote switch.

rem-intf rem-intf-number

Displays the remote interface number.

rem-ports port-list

Displays the remote switch ports.

peer-intf peer-intf-number

Displays the peer interface number.

peer-state active|static|vrrp|tunnel|software|needs-peer-status|port-mac|hit|ageout-check|moving|loop-probe|local-tunnel|igmp-mac|user-flush|vxlan-loopback|router|update-peer-only|        active-state-mismatch|peer-port-missing|peer-port-not-vlag|peer-port-not-orphaned|peer-port-not-cluster-link|sw-active|anycast|hsrp|invalid-vlan|owner-lost|cluster-link-down|vxlan-router|peer-force-resync|excess-mac-move-detected|excess-ip-move-detected|retry|evpn|evpn-wo-bgp|evpn-def-gw| evpn-delete

Displays the state of the peer vPorts.

peer-owner-state active|static|vrrp|tunnel|software|needs-peer-status|port-mac|hit|ageout-check|moving|loop-probe|local-tunnel|igmp-mac|user-flush|vxlan-loopback|router|update-peer-only|active-state-mismatch|peer-port-missing|peer-port-not-vlag|peer-port-not-orphaned|        peer-port-not-cluster-link|sw-active|anycast|hsrp|invalid-vlan|owner-lost|cluster-link-down|vxlan-router|peer-force-resync|excess-mac-move-detected|excess-ip-move-detected|retry|evpn|        evpn-wo-bgp|evpn-def-gw|evpn-delete

Displays the state of the peer owner vPorts.

status phy-up|up|disabled|hw-nat-loop|mirror-loop|mirror-to|PN-switch|PN-fabric|PN-other|PN-cluster|PN-internal|host|uplink|STP-BPDUs|LLDP|trunk|l3-port|remote-l3-port|dhcp|        dhcpsvr|blocked|no-BPDU|LACP-PDUs|vlag-active|vlag-blocked|stp-edge-port|LACP-wait|LACP-fallback|adjacency-wait|        adjacency-check|vlag-wait|multicast-router|loop|congested|vxlan-loopback|vlan-up|vle|vle-wait|phy-down|down|enabled|err-disabled|err-bpdu-guard|mac-violation|stp-bpdu-guard|stp-root-guard|defer-bringup-wait

Displays the vPort status.

vtep-ip ip-address

Displays the VTEP IP address.

tunnel tunnel-string

Displays the vPort tunnel.

create-time date/time: yyyy-mm-ddTHH:mm:ss

Displays the vPort create time.

last-seen date/time: yyyy-mm-ddTHH:mm:ss

Displays the last time the vPorts was seen.

vxlan-lru date/time: yyyy-mm-ddTHH:mm:ss

Displays the time and date of the VXLAN LRU.

hit hit-number

Displays the number of hits.

migrate migrate-number

Displays the number of times the entry migrated.

drops drops-number

Displays the number of dropped packets.

hw-index hw-index-number

Displays the hardware index number.

rt-if rt-if-string

Displays the router interface.

hw-flags invalid-vlan|invalid-port

Displays hardware flags.

mc-index mc-index-number

L2 multicast group index in hardware.

Defaults   None

Access   CLI

History   

Version 2.2

Command introduced.

Version 2.2.6

The parameters, stp-edge-port|LACP-wait| adjacency-wait|adjacency-check|vlag-wait|multicast-router, added.

Version 2.3

The parameters, num-ips and vm-status, added.

Version 2.4.1

The parameter, public-vlan, added.

Version 2.6.2

The parameter, svc-name, power, entity, portgroup, pg-vlans, vswitch, vs-type, and vnic-type, added.

The parameters, hypervisor, vm-id, vm-name, vm-flavor, vm-status, memory, deprecated.

Version 3.0.0

The options, anycast, invalid-vlan, and owner-lost, added to state, peer-state, and peer-owner-state.

Version 3.1.0

The parameters vtep-ip and ND added.

Version 6.1.0

The options evpn, evpn-wo-bgp, evpn-def-gw, evpn-delete added to state, peer-state, and peer-owner-state.

Version 

The option host-disabled deprecated.

Usage   Use this command to display vPort information on the switch. Netvisor mirrors vPorts  across the fabric so every switch knows about all the L2 entries on the fabric. You may find this useful for troubleshooting connections across the fabric.

Examples  To display vPorts, use the following syntax:

CLI network-admin@switch > vport-show format all layout vertical

mac:          66:0e:94:21:64:74

vlan:         103

config-intf:  70

config:       port

switch-id:    pleiades24

mac:          00:00:5e:00:01:0a

vlan:         107

config:       switch

rem-switch:   pleiades25

switch-id:    pleiades25

mac:          66:0e:94:21:a9:6c

vlan:         100

ip:           192.168.11.4

intf:         65

ports:        65

state:        active

hostname:     pleiades25

status:       PN-internal

create-time:  09-10,15:17:47

last-seen:    09-15,10:55:22

hit:          2

migrate:      1

switch-id:    pleiades24

mac:          66:0e:94:21:64:74

vlan:         100

ip:           192.168.100.12

intf:         65

ports:        65

hostname:     pleiades24

status:       PN-internal

create-time:  09-10,15:17:48

last-seen:    09-10,15:17:48

hit:          1

switch-id:    pleiades24

north
    keyboard_arrow_up
    keyboard_arrow_down
    description
    print
    feedback
    support
    business
    rss_feed
    south