vrouter-interface-config-modify
This command is used to modify routing protocol configuration to a vRouter.
Syntax vrouter-interface-config-modify
|
vrouter-name name-string |
Specify the vRouter name to add the interface. |
|
Specify the following interface configuration arguments: |
|
|
nic vrouter-interface-nic |
Specify the NIC to modify. |
|
l3-port l3port-usable-port name |
Specify the Layer 3 port to modify. |
|
ospf-hello-interval seconds |
Specify the OSPF hello interval with a number between 1 and 65535. This configures the interval between sending OSPF hello messages on an interface. The default value is 10. |
|
ospf-dead-interval seconds |
Specify the OSPF dead interval with a number between 2 and 65535. This configures the interval in which the vRouter must receive an OSPF hello message before the state of the neighbor changes to down. The default interval is 5. |
|
ospf-retransmit-interval seconds |
Specify the OSPF retransmit interval from 3 to 65535 seconds. The default is 5 seconds. (IPv4 orIPv6) |
|
ospf-priority number |
Specify the OSPF priority with a number between 0 and 255. A vRouter with a priority of 0 does not participate in the designated router decision. The default value is 1. |
|
ospf-auth-key ospf-auth-key-string |
Specify an authorization key string for the vRouter interface. |
|
ospf-cost number |
Specify the OSPF cost with a value between 0 and 655365. |
|
ospf-msg-digest-id id |
Specify a value between 0and 255. If you specify 0, then OSPF MD5 authentication is not set. |
|
ospf-msg-digest-key ospf-msg-digest-key-string |
Specify a string for the OSPF message digest key. |
|
ospf-passive-if|no-ospf-passive-if |
Specify if the OSPF interface is passive or not. |
|
ospf-network-type default|point-to-point |
Specify the type of OSPF network. |
|
ospf-bfd default|enable|disable |
Specify if BFD protocol support for OSPF fault detection is enabled. The default is Disable. |
|
bfd-interval interval |
Specify the desired Bidirectional Forwarding Detection (BFD) transmit interval from 200 ms to 3000 ms. The default value is 750 ms. |
|
bfd-min-rx interval |
Specify the required BFD receive interval from 200 milliseconds to 3000 milliseconds. The default value is 500 milliseconds. |
|
bfd-multiplier integer |
Specify the BFD detection multiplier from 2 to 20. The default value is 3. |
|
nd-suppress-ra|no-nd-suppress-ra |
Specify if you want to suppress the transmit of IPv6 router advertisements. |
|
v6-ra-prefix ip-address |
Specify the IPv6 prefix to include in router advertisements. |
|
prefix-netmask netmask |
Specify the IPv6 prefix netmask. |
|
autoconf|no-autoconf |
Specify if you want the prefix used for IPv6 autoconfiguration. |
|
ra-interval seconds |
Specify the interval between router advertisements in seconds with a range of 1 to 1800 seconds. |
|
ra-lifetime seconds |
Specify the time that the vRouter is considered as the default router in seconds with a range of 0 to 9000. |
Defaults None
Access CLI
History
|
Version 2.1 |
Command introduced. |
|
Version 2.2 |
The parameter, ospf-cost, added. |
|
Version 2.2.2 |
The parameters, ospf-msg-digest-key, and ospf-msg-digest-id, added. |
|
Version 2.2.3 |
The parameters ospf-passive-if and no-ospf-passive-if added. |
|
Version 2.2.6 |
The parameters, bfd-interval, bfd-min-rx, and bfd-multiplier, added. |
|
Version 2.4.1 |
The parameter, ospf-network-type, added. |
|
Version 2.5 |
The parameters, nd-suppress-ra, v6-ra-prefix, prefix-netmask, autoconf|no-autoconf, ra-interval, and ra-lifetime added. |
|
Version 2.5.3 |
The parameter, ospf-bfd default|enable|disable added. |
|
Version 3.0.0 |
The parameters, ospf-retransmit-interval,ra-prefix, ra-interval added. |
|
Version 5.1.3 |
The parameter, l3-port, added. |
Usage This command is used to modify a routing protocol configuration to a vRouter.
Examples To modify an interface to vRouter, vroute-int, interface eth0.11, hello interval 10, dead interval 20, with priority 5, use the following command:
CLI network-admin@switch > vrouter-interface-config-modify vrouter-name vroute-int nic eth0.11 ospf-hello-interval 10 ospf-dead-interval 20 ospf-priority 5
To remove OSPF authentication key from a configuration, use empty double quotes as shown below:
CLI network-admin@switch > vrouter-interface-config-modify ospf-auth-key ""