port-phy-show
This command is used to display information about the physical Layer 1 status of the local switch.
Syntax port-phy-show
port port-list |
Specifies the switch data port number, list of ports, or range of ports. Port numbers must be in the range of 1-64. |
bezel-port bezel-port-string |
Specifies the bezel port. |
state off|admin-down|adminpwrdown|bist|dfe-tuning|down|local-fault|partially-up|remote-fault|up|failed |
Specifies the state of the port PHY. |
mode off|admin-down|adminpwrdown|bist|dfe-tuning|down|local-fault|partially-up|remote-fault|up|failed |
Specifies the mode of the port PHY. |
autoneg autoneg-string |
Specifies the auto-negotiation setting of the port PHY. |
speed speed-number |
Specifies the speed of the port PHY. |
eth-mode configured 1000base-x|sgmii|disabled|1000base-kx|2500base-x|6Gbase-kr|6Gbase-cr|10Gbase-kr|10Gbase-cr|10Gbase-sr|AN-73|Xaui|10Gbase-kx4|10Gbase-cx4|24Gbase-kr4|24Gbase-cr4|40Gbase-kr4| XLaui|40Gbase-cr4| |
Specify the Ethernet mode as 1000 base or Serial Gigabit Media Independent Interface (SGMII). |
max-frame max-frame-number |
Specifies the maximum number of frames. |
def-vlan def-vlan-number |
Specifies the default VLAN identifier of the port PHY. |
fec fec-string |
Specifies the FEC. |
Defaults None.
Access CLI
History
Version 1.2 |
Command introduced. |
Version 2.1 |
The parameter eth-mode added. |
Version 2.2 |
The options, disabled|1000base-kx|2500base-x|6Gbase-kr|6Gbase-cr|10Gbase-kr|10Gbase-cr|10Gbase-sr|AN-73|Xaui|10Gbase-kx4|10Gbase-cx4|24Gbase-kr4|24Gbase-cr4|40Gbase-kr4| XLaui|40Gbase-cr4|40Gbase-sr4|no-phy-present|MII|GMII|TBI|10G-XGMII|1G-RGMII|10G-SFI|10G-XFI added. |
Version 3.0.0 |
The parameter link-quality deprecated. |
Version 3.1.0 |
The parameters GII and disabled added. |
Version 7.0.0 |
The parameter bezel-port added. |
Usage Switches are equipped with network data ports for host or inter-switch communication. Use this command to display the status of network data ports on the local switch.
Examples To display the status of network data ports on the switch, use the following command:
CLI (network-admin@switch) > port-phy-show
switch port bezel-port state speed eth-mode max-frame def-vlan
------ ---- ---------- ----- ------ --------- --------- --------
switch 1 1 down 100000 sr4 1540 1
switch 2 1.2 down 25000 10G-XGMII 1540 1
switch 3 1.3 down 25000 10G-XGMII 1540 1
switch 4 1.4 down 25000 10G-XGMII 1540 1
switch 5 2 down 100000 caui4 1540 1
switch 6 2.2 down 25000 10G-XGMII 1540 1
switch 7 2.3 down 25000 10G-XGMII 1540 1
switch 8 2.4 down 25000 10G-XGMII 1540 1