trunk-show

This command displays the list of links aggregated into a trunk.

Syntax   trunk-show

name name-string

The name for the trunk configuration.

ports port-list

The port number(s) for the link(s) to aggregate into the trunk.

Specify any of the following options:

speed disable|100m|1g|10g|40g|50g|100g

Specify the port speed or disable the port.

egress-rate-limit unlimited

Specify an egress rate limit for the configuration.

autoneg|no-autoneg

Specify if you want the physical port to autonegotiate port speed.

jumbo|no-jumbo

Specify if the port can receive jumbo frames.

lacp-mode off|passive|active

Specify the Link Aggregation Control Protocol (LACP) mode for the configuration.

lacp-priority number

Specify the LACP priority. This is a number between 1 and 65535 with a default value of 32768.

lacp-timeout slow|fast

Specify the LACP time out as slow (30 seconds) or fast (4 seconds). The default value is slow.

lacp-fallback bundle|individual

Specify the LACP fallback mode as individual or bundled.

lacp-fallback-timeout seconds

Specify the LACP fallback timeout in seconds. The range is between 30 and 60 seconds with a default value of 50 seconds.

reflect|noreflect

Specify physical port reflection

edge-switch|no-edge-switch

Specify if the switch is an edge switch.

pause|no-pause

Specify if pause frames are sent.

description description-string

Specify the physical port description.

loopback|no-loopback

Specify loopback if you want to use loopback.

vxlan-termination|
no-vxlan-termination

Specify if a VXLAN can terminate on the trunk.

unknown-ucast-level unknown-ucast-level-string

Specify an unknown unicast level in percent. The default value is 100%.

unknown-mcast-level unknown-mcast-level-string

Specify an unknown multicast level in percent. The default value is 100%.

broadcast-level broadcast-level-string

Specify a broadcast level in percent. The default value is 100%.

port-mac-address mac-address

Specify the MAC address of the port.

loop-vlans vlan-list

Specify a list of VLANS for looping.

routing|no-routing

Specify if the port participates in routing on the network.

host-enable|host-disable

Enable or disable host facing ports.

defer-bringup|no-defer-bringup

Specify to delay bringing up the host.

dscp-map dscp-map name|none

Specify the DSCP map name to enable on a port

local-switching|no-local-switching

Specify local-switching or no-local-switching. A no-local-switching port cannot bridge traffic to another no-local-switching port

allowed-tpid q-in-q|q-in-q-old

Specify an allowed TPID in addition to 0x8100 for VLAN headers.

fabric-guard|no-fabric-guard

Specify if fabric guard is enabled.

fec|no-fec

Specify Port Forwarding Error Correction (FEC) mode.

Defaults   None.

Access   CLI

History   

Version 1.2

Command introduced.

Version 1.2.6

The optional parameter, lacp-mode, was added.

Version 2.1

The parameter id is deprecated. The parameters, enable | disable, lacp-priority, lacp-timeout, reflect, edge-switch, pause, description, loopback, mirror-receive, port-mac, and send-port added.

Version 2.2.5

The parameters, unknown-ucast-level, unknown-mcast-level, and broadcast-level added.

Version 2.2.6

The parameter, egress-rate-limit, added.

Version 2.3

The parameters, auto-neg, eth-mode, and reflect deprecated.The parameter, rem-rswitch-port and routing, added.

Version 2.4

The parameter, enable|disable, deprecated. The parameters, loop-vlans and host-enable, added.

Version 2.5.3

The parameters, reflect|noreflect, dscp-map dscp-map name|none, and local-switching|no-local-switching, added.

Version 2.6.2

The parameter, vxlan-termination, allowed-tpid, and fabric-guard, added. The parameter, mirror-receive-only, deprecated.

Version 3.0.0

The parameter, autoneg|no-autoneg, added.

Version 3.1.0

The parameter, fec|no-fec, added.

Version 5.1.0

The parameters, bw-bps, rem-rswitch-port-mac, deprecated. The parameter, defer-bringup|no-defer-bringup, added.

Version 7.0.0

The parameter description added.


Usage   Trunks can be used to aggregate network links at Layer 2 on the local switch. Use this command to modify the links for a trunk.


Examples  To display a list of all trunks and the aggregated links, use the following command:

CLI (network-admin@switch) > trunk-show

name    port speed autoneg jumbo

------- ---- ----- ------- ----

trunk-1 1,3  10g   off     off

north
    keyboard_arrow_up
    keyboard_arrow_down
    description
    print
    feedback
    support
    business
    rss_feed
    south