vrouter-show
This command displays a virtual router (vRouter) service for a fabric, cluster, or standalone switch.
Syntax vrouter-show
id |
The ID number assigned to the configuration. |
name name-string |
Specifies the name of the vRouter. |
type vnet-mgr|vrouter|netzone|orphaned|netvm| nat|ovs |
Specifies the type of vRouter. |
scope local|fabric |
Specifies the scope of the vRouter. |
vnet vnet-name |
Specifies the name of the vNET. |
location fabric-node-name |
Specifies the location of the vRouter on the fabric. |
router-type hardware|software |
Specifies the router type as hardware or software. |
hw-router-mac mac-address |
Specifies the MAC address of the hardware router. |
fabric-comm |
Specifies if Netvisor uses the vRouter as a fabric communication interface. |
router-ipstack quagga|frr |
Specifies the type of vRouter IP stack. |
evpn-border|no-evpn-border |
Enable or disable EVPN border gateway. |
evpn-dup-addr-max-moves 2..1000 |
Specify the maximum number of EVPN duplicate address moves. The default value is 5. |
evpn-dup-addr-moves-duration 2..1800 |
Specify the EVPN duplicate address move time duration. The default vale is 180s. |
evpn-dup-addr-freeze none|permanent|-1..3600 |
EVPN duplicate address freeze duration (seconds). The default value is 180s. By default, if 5 MAC moves are detected in a 180s time window, the duplicate MAC address entry is frozen for 180s. |
hw-vrid hw-vrid-number |
Specifies the virtual router ID of the hardware router. |
hw-vrrp-id hw-vrrp-id-number |
Specifies the VRRP ID for a hardware router. |
bgp-as bgp-as-number |
Specifies the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP). |
router-id ip-address |
Specifies the vRouter IP address |
proto-multi none|vmrp|pim-ssm |
Specifies the optional multicast protocol for the vRouter service. Select none, Vector Multicast Routing Protocol (VMRP), or Protocol Independent Multicast-source specific mode (PIM-SIM). |
bgp-redistribute static|connected|rip|ospf |
Specify how BGP routes are redistributed. |
bgp-redist-static-metric none |
Specify a static metric for BGP route redistribution. |
bgp-redist-connected-metric none |
Specify a connected metric for BGP route redistribution |
bgp-redist-rip-metric none |
Specify a RIP metric for BGP route redistribution. |
bgp-redist-ospf-metric none |
Specify a OSPF metric for BGP route redistribution. |
bgp-cluster-id ip-address |
Specify an IP address for a BGP cluster. |
bgp-max-paths bgp-max-paths-number |
Specify the maximum number of paths for BGP. |
bgp-ibgp-multipath bgp-ibgp-multipath-number |
Specify the number of multipaths for BGP. |
bgp-bestpath-as-path none|ignore |
Specify a parameter for a best path as path. |
bgp-dampening| |
Specify a BGP damp |
bgp-graceful-restart| |
Specify a graceful restart for BGP routing. |
bgp-stalepath-time second |
Specify the length of time befor a BGP path becomes stale. This is a value between 0, and 3600. |
bgp-scantime seconds |
Specify a BGP scanner interval in seconds. The default interval is 60 seconds with a range of 5 to 60 seconds. |
bgp-keepalive-interval seconds |
Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds. |
bgp-holdtime seconds |
Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds. |
bgp-distance-external integer |
Specify the BGP distance for routes external to the AS. |
bgp-distance-internal integer |
Specify the BGP distance for routes internal to the AS. |
bgp-distance-local integer |
Specify the BGP distance for routes local to the AS. |
bgp-ipv4-unicast| |
Specify a MP-BGP Control default IPv4 Unicast AFI/SAFI. |
rip-redistribute static|connected|ospf| |
Specify how RIP routes are redistributed. |
ospf-redistribute static|connected|rip| |
Specify how OSPF routes are redistributed. |
vrrp-track-port port-list |
Specify a port to track a VRRP configuration. |
ospf-redist-static- |
Specify a static metric type for OSPF route redistribution. |
ospf-distance-external integer |
Specify the OSPF distance for routes external to the AS. |
ospf-distance-internal integer |
Specify the OSPF distance for routes internal to the AS. |
ospf-distance-local integer |
Specify the OSPF distance for routes local to the AS. |
ospf-stub-router-on-startup| |
Specify if you want advertise self as stub router temporarily on startup. |
ospf-stub-router-on-startup-period integer |
Specify the time period to advertise self as stub router on startup. This s a value between 5, and 86400 seconds. |
ospf-bfd-all-if| |
Specify if you want to use BFD protocol for fault detection on all OSPF interfaces. |
ospf-default-information none|originate|always |
Specify if you want to control origination of default route. |
ospf-default-info-originate- |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate-metric-type 1|2 |
Specify the metric type for OSPF origination of default route. |
ospf-redist-connected- |
Specify a connected metric type for OSPF route redistribution. |
ospf-redist-connected- |
Specify a connected metric type for OSPF route redistribution. |
ospf-redist-rip-metric none |
Specify a RIP metric type for OSPF route redistribution. |
ospf-redist-rip-metric-type 1|2 |
Specify a RIP metric type for OSPF route redistribution. |
ospf-redist-bgp-metric none |
Specify a BGP metric type for OSPF route redistribution. |
ospf-redist-bgp-metric-type 1|2 |
Specify a BGP metric type for OSPF route redistribution. |
ospf6-redistribute static|connected|bgp4 |
Specify if you want to redistribute OSPF6 routes. |
ospf6-redist-static-metric none |
Specify a metric for OSPF6 redistribute of static routes. |
ospf6-redist-static-metric- |
Specify a metric type for OSPF6 redistribution of static routes. |
ospf6-redist-connected-metric none |
Specify a metric for OSPF6 redistribution of connected routes. |
ospf6-redist-connected-metric-type 1|2 |
Specify a metric type for OSPF6 redistribution. |
ospf-default-information none|originate|always |
Specify how to control the origination of default route. |
ospf-default-info-originate-metric none |
Specify the metric for OSPF origination of default route. |
ospf-default-info-originate-metric- |
Specify the metric type for OSPF origination of default route. |
ospf-default-info-originate-route- |
Specify the route map for OSPF origination of default route. |
bgp-snmp|no-bgp-snmp |
Enable or disable BGP SNMP MIB. |
bgp-snmp-notification|no-bgp-snmp-notification |
Enable or disable SNMP notifications for BGP MIBs. |
ospf-snmp|no-ospf-snmp |
Enable or disable OSPF SNMP MIB. |
ospf-snmp-notification|no-ospf-snmp-notification |
Enable or disable SNMP notifications for OSPF MIBs. |
ospf6-snmp|no-ospf6-snmp |
Enable or disable OSPFv3 SNMP MIB. |
ospf6-snmp-notification|no-bgp-snmp-notification |
Enable or disable SNMP notifications for OSPFv3 MIBs. |
ip-snmp|no-ip-snmp |
Enable or disable ipForward SNMP MIBs. |
no-bgp-redist-static-route-map |
Remove route map for BGP static redistribution. |
no-bgp-redist-connected-route-map |
Remove route map for BGP connected redistribution. |
no-bgp-redist-ospf-route-map |
Remove route map for BGP OSPF redistribution. |
Defaults None.
Access CLI
History
Version 1.2 |
Command introduced. |
Version 2.0 |
Parameter type added. |
Version 2.2 |
The parameter location, hw-router-mac, and hw-vrrp-id added. The parameters bgp-redistribute, rip-redistribute, and ospf-redistribute added. |
Version 2.2.3 |
The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added |
Version 2.3.1 |
The parameters ospf6- added. |
Version 2.4 |
The parameters ospf-stub-router-on-startup, and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added. |
Version 2.4.1 |
The parameter bgp-distance-, and ospf-distance- added. |
Version 2.5.4 |
The parameter shared-vnet-mgr added. |
Version 2.6 |
SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added. |
Version 3.0.0 |
The parameters ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added. |
Version 3.1.0 |
The parameters for route maps added. |
Version 6.1.0 |
The parameter evpn-border|no-evpn-border added |
Version 6.1.1 |
The parameters evpn-dup-addr-max-moves, evpn-dup-addr-moves-duration, and evpn-dup-addr-freeze added. |
Usage Each fabric, cluster, standalone switch, or virtual network (vNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks, and implements Layer 3 protocols. This command displays vRouter service.
Examples To display the configuration for vRouter1, use the following command:
CLI (network-admin@switch) > vrouter-show name vRouter1 format all layout vertical
id: c00029d:0
name: vRouter1
type: vrouter
scope: fabric
vnet:
location: switch
zone-id: c00029d:1
router-type: hardware
evpn-border: enable