port-config-show
This command is used to display port settings on the switch.
Syntax port-config-show
|
port port-list |
A port or list of ports. |
|
speed disable|10m|100m|1g|2.5g|10g|25g|40g|50g|100g|200g|400g |
The port speed. Ports configured for speeds of 1G must be equipped with SFP transceivers. Ports configured for 10G or higher must be equipped with SFP+ or QSFP+ transceivers. |
|
bw-bps bw-bps-number |
Specify the bandwidth bps for the port. |
|
egress-rate-limit unlimited |
The egress rate limit for the port. |
|
eth-mode unconfigured|disabled|1000base-x|sgmii|1000base-kx|2500base-x| 6Gbase-kr|6Gbase-cr|10Gbase-kr|10Gbase-cr|10Gbase-sr|AN-73| Xaui|10Gbase-kx4|10Gbase-cx4|24Gbase-kr4|24Gbase-cr4|40Gbase-kr4|xlaui|40Gbase-cr4|40Gbase-sr4|no-phy-present|MII|gmii|TBI|10G-XGMII|1G-RGMII|sfi|xfi|cx|kr4|sr4|lr4|er4|cr4|cx4|kx4|caui4|kr2|er2|cr2|sr2|lr2|xlaui2|cx2|sr|lr|er|cr|kx|kr|zr|base-x|sys-default|caui|aoc|xlppi|psm4|base_t|base_cx|base_lx|base_sx |
The Ethernet mode. |
|
autoneg|no-autoneg |
Displays if the port auto-negotiates the port speed with a peer. |
|
jumbo|no-jumbo |
Displays if the port forwards jumbo frames. Jumbo frames are Ethernet frames with more than 1500 bytes of payload. |
|
enable|disable |
Displays if the port is enabled, and forwards or drops frames. |
|
lacp-priority integer |
The LACP priority for the port. This is a value between 1, and 65535 with a default value of 32768. |
|
reflect|no-reflect |
Displays if the port reflects frames received for loopback testing. |
|
edge-switch|no-edge-switch |
Displays if the port connects to another Pluribus Networks device or is an uplink to a third-party switch or host. |
|
pause|no-pause |
Displays if the port traffic is paused or not. |
|
description description-string |
A description for the port. |
|
loopback|no-loopback |
Displays to use loopback or no loopback. |
|
vxlan-termination|no-vxlan-termination |
Displays if a VXLAN terminates on a port. |
|
mirror-only|no-mirror-receive-only |
Displays if you want the port to receive mirrored traffic only. |
|
vle vle name |
The vLE on this port. |
|
updown_time high resolution time: #ns |
The updown time. |
|
send-port send-port-number |
The port number to send in packets. |
|
loop-vlans vlan-list |
The VLANs that are looping on the network. |
|
routing|no-routing |
Displays if the port is participating in routing on the switch. |
|
cluster-port|no-cluster-port |
Specifies whether the port is a cluster port. |
|
defer-bringup|no-defer-bringup |
Specify if you want to delay port activation. |
|
host-enable|host-disable |
Displays if you want host-facing ports enabled or disabled. |
|
crc-check-enable|crc-check-disable |
Displays if you want CRC checking performed by the port. This is applicable to a switch in Virtual Wire mode. The default value is crc-check-disable. |
|
dscp-map dscp-map name|none |
A DSCP map name to enable on port. |
|
local-switching|no-local-switching |
Displays if local switching is allowed on the port. |
|
allowed-tpid vlan|q-in-q|q-in-q-old |
Specify the allowed TPID in addition to 0x8100 on VLAN header |
|
rhost rhost-string |
The physical remote host. |
|
fabric-guard|no-fabric-guard |
Displays if user wants loop detection enabled on the port. |
|
fec|no-fec |
The port forward error correction (FEC) mode. |
Defaults None.
Access CLI
History
|
Version 1.2 |
Command introduced. |
|
Version 1.2.6 |
The optional parameters for LACP added. |
|
Version 2.1 |
The parameters loopback, mirror-receive, vlag-failover, and send-port added. |
|
Version 2.2.6 |
The parameter egress-rate-limit, introduced. |
|
Version 2.3.1 |
Multiple parameters for LACP added. |
|
Version 2.4 |
The parameter host-enable, and loop-vlans added. |
|
Version 2.4.1 |
The parameters lacp-fallback, lacp-fallback-timeout, and lacp-individual deprecated. |
|
Version 2.5.2 |
The parameter crc-check-enable|crc-check-disable, introduced. |
|
Version 2.5.3 |
The parameters reflect|no-reflect, vxlan-termination, dscp-map, and local-switching added. |
|
Version 2.6.0 |
The parameter fabric-guard, and allowed-tpid added. |
|
Version 3.0.0 |
The parameter bw-bps added. |
|
Version 5.1.0 |
The following parameter deprecated: • bw-bps The following parameters introduced: • additional Ethernet modes • defer-bringup|no-defer-bringup • fec|no-fec|fec-auto |
Usage Server-switches are equipped with network data ports for host or inter-switch communication. This command configures the settings of a specific network data port of all data ports on the local switch.
Examples To display information about all ports on a switch, use the following command:
CLI (network-admin@switch) > port-config-show
switch: pleiades25
intf: 10
name:
port: 10
speed: 10g
autoneg: off
jumbo: off
enable: on
lacp-priority: 32768
reflect: off
edge-switch: no
pause: no
description:
loopback: default
mirror_only: default
rswitch-default-vlan: 0
port-mac-address: 06:b0:00:02:30:0a