vrouter-interface-config-add
This command is used to add additional routing protocol configuration to a vRouter.
Syntax vrouter-interface-config-add
|
vrouter-name name-string |
Specify the vRouter name to add the interface. |
|
Specify the following interface configuration arguments: |
|
|
nic vrouter-interface-nic |
Specify the NIC to add to the interface. |
|
l3-port l3port-usable-port name |
Specify a Layer 3 port to add to the interface. |
|
ospf-hello-interval seconds |
Specify the OSPF hello interval with a number between 1, and 65535. This configures the interval between sending OSPF hello messages on an interface. The default value is 10. |
|
ospf-dead-interval seconds |
Specify the OSPF dead interval with a number between 2, and 65535. This configures the interval in which the vRouter must receive an OSPF hello message before the state of the neighbor changes to down. The default interval is 5. |
|
ospf-retransmit-interval seconds |
Specify the OSPF retransmit interval from 3 to 65535 seconds. The default is 5 seconds. (IPv4 orIPv6) |
|
ospf-priority number |
Specify the OSPF priority with a number between 0, and 255. A vRouter with a priority of 0 does not participate in the designated router decision. The default value is 1. |
|
ospf-auth-key ospf-auth-key-string |
Specify an authorization key string for the vRouter interface. |
|
ospf-cost number |
Specify the OSPF cost with a value between 0, and 655365. |
|
ospf-msg-digest-id id |
Specify a value between 0and 255. If you specify 0, then OSPF MD5 authentication is not set. |
|
ospf-msg-digest-key ospf-msg-digest- |
Specify a string for the OSPF message digest key. |
|
ospf-passive-if| |
Specify if the OSPF interface is passive or not. |
|
ospf-network-type default|point-to-point |
Specify the type of OSPF network. |
|
ospf-bfd default|enable|disable |
Specify if BFD protocol support for OSPF fault detection is enabled. The default is Disable. |
|
bfd-interval interval |
Specify the desired Bidirectional Forwarding Detection (BFD) transmit interval from 200 ms to 3000 ms. The default value is 750 ms. |
|
bfd-min-rx interval |
Specify the required BFD receive interval from 200 milliseconds to 3000 milliseconds. The default value is 500 ms. |
|
bfd-multiplier integer |
Specify the BFD detection multiplier from 2 to 20. The default value is 3. |
|
nd-suppress-ra|no-nd-suppress-ra |
Specify if you want to suppress the transmit of IPv6 router advertisements. |
|
v6-ra-prefix ip-address |
Specify the IPv6 prefix to include in router advertisements. |
|
prefix-netmask netmask |
Specify the IPv6 prefix netmask. |
|
autoconf|no-autoconf |
Specify if you want the prefix used for IPv6 autoconfiguration. |
|
ra-interval seconds |
Specify the interval between router advertisements in seconds with a range of 1 to 1800 seconds. |
|
ra-lifetime seconds |
Specify the time that the vRouter is considered as the default router in seconds with a range of 0 to 9000. |
Defaults None
Access CLI
History
|
Version 2.1 |
Command introduced. |
|
Version 2.2 |
The parameter ospf-cost added. |
|
Version 2.2.2 |
The parameters ospf-msg-digest-key, and ospf-msg-digest-id added. |
|
Version 2.2.3 |
The parameters ospf-passive-if, and no-ospf-passive-if added. |
|
Version 2.2.6 |
The parameters bfd-interval, bfd-min-rx, and bfd-multiplier added. |
|
Version 2.4.1 |
The parameter ospf-network-type added. |
|
Version 2.5 |
The parameters nd-suppress-ra, v6-ra-prefix, prefix-netmask, autoconf|no-autoconf, ra-interval, and ra-lifetime added. |
|
Version 2.5.3 |
The parameter ospf-bfd default|enable|disable added. |
|
Version 3.0.0 |
The parameters ospf-retransmit-interval,ra-prefix, ra-interval added. |
|
Version 5.1.3 |
The parameter l3-port added. |
Usage This command is used to add additional routing protocol configuration to a vRouter.
Examples To add an interface to vRouter, vroute-int, interface eth0.11, hello interval 10, dead interval 20, with priority 5, use the following command:
CLI (network-admin@switch) > vrouter-interface-config-add vrouter-name vroute-int nic eth0.11 ospf-hello-interval 10 ospf-dead-interval 20 ospf-priority 5