vrouter-show

This command displays a virtual router (vRouter) service for a fabric, cluster, or standalone switch.

Syntax   vrouter-show

id

The ID number assigned to the configuration.

name name-string

Specifies the name of the vRouter.

type vnet-mgr|vrouter|netzone|orphaned|netvm|nat|ovs

Specifies the type of vRouter.

scope local|fabric

Specifies the scope of the vRouter.

vnet vnet-name

Specifies the name of the VNET.

location fabric-node-name

Specifies the location of the vRouter on the fabric.

router-type hardware|software

Specifies the router type as hardware or software.

hw-router-mac mac-address

Specifies the MAC address of the hardware router.

fabric-comm

Specifies if NetVisor uses the vRouter as a fabric communication interface.

router-ipstack quagga|frr

Specifies the type of vRouter IP stack.

evpn-border|no-evpn-border

Enable or disable EVPN border gateway.

evpn-dup-addr-max-moves 2..1000

Specify the maximum number of EVPN duplicate address moves. The default value is 5.

evpn-dup-addr-moves-duration 2..1800 

Specify the EVPN duplicate address move time duration. The default vale is 180s.

evpn-dup-addr-freeze none|permanent|-1..3600

EVPN duplicate address freeze duration (seconds). The default value is 180s. By default, if 5 MAC moves are detected in a 180s time window, the duplicate MAC address entry is frozen for 180s.

hw-vrid hw-vrid-number

Specifies the virtual router ID of the hardware router.

hw-vrrp-id hw-vrrp-id-number

Specifies the VRRP ID for a hardware router.

bgp-as bgp-as-number

Specifies the Autonomous System Number (ASN) if the vRouter runs Border Gateway Protocol (BGP).

router-id ip-address

Specifies the vRouter IP address

proto-multi none|vmrp|pim-ssm

Specifies the optional multicast protocol for the vRouter service. Select none, Vector Multicast Routing Protocol (VMRP), or Protocol Independent Multicast-source specific mode (PIM-SIM).

bgp-redistribute static|connected|rip|ospf

Specify how BGP routes are redistributed.

bgp-redist-static-metric none

Specify a static metric for BGP route redistribution.

bgp-redist-connected-metric none

Specify a connected metric for BGP route redistribution

bgp-redist-rip-metric none

Specify a RIP metric for BGP route redistribution.

bgp-redist-ospf-metric none

Specify a OSPF metric for BGP route redistribution.

bgp-cluster-id ip-address

Specify an IP address for a BGP cluster.

bgp-max-paths bgp-max-paths-number

Specify the maximum number of paths for BGP.

bgp-ibgp-multipath bgp-ibgp-multipath-number

Specify the number of multipaths for BGP.

bgp-bestpath-as-path none|ignore

Specify a parameter for a best path as path.

bgp-dampening|no-bgp-dampening

Specify dampening for BGP routes.

bgp-delayed-startup 0..36000

Displays the delayed time interval in forming peer adjacency during bootup. BGP neighbors are not brought up until the timer's expiry. The default value is 0. 

bgp-network-import-check|no-bgp-network-import-check

Specifies whether BGP network route exists in IGP.

bgp-update-delay-strict 0..3600

Displays the time interval to put BGP read-only mode during bootup. BGP neighbors are brought up and receives the peer routes but local routes are not advertised until the timer's expiry. The default value is 0.

bgp-keepalive-interval seconds

Specify a BGP keepalive interval in seconds. The default is 60 seconds with a range of 0 to 65535 seconds.

bgp-holdtime seconds

Specify a BGP holdtime in seconds. The default is 180 seconds with a range of 0 to 65535 seconds.

bgp-distance-external integer

Specify the BGP distance for routes external to the AS.

bgp-distance-internal integer

Specify the BGP distance for routes internal to the AS.

bgp-distance-local integer

Specify the BGP distance for routes local to the AS.

bgp-ipv4-unicast|no-bgp-ipv4-unicast

Specify a MP-BGP Control default IPv4 Unicast AFI/SAFI.

rip-redistribute static|connected|ospf|bgp

Specify how RIP routes are redistributed.

ospf-redistribute static|connected|rip|bgp

Specify how OSPF routes are redistributed.

vrrp-track-port port-list

Specify a port to track a VRRP configuration.

ospf-redist-static-metric-type 1|2

Specify a static metric type for OSPF route redistribution.

ospf-distance-external integer

Specify the OSPF distance for routes external to the AS.

ospf-distance-internal integer

Specify the OSPF distance for routes internal to the AS.

ospf-distance-local integer

Specify the OSPF distance for routes local to the AS.

ospf-stub-router-on-startup|no-ospf-stub-router-on-startup

Specify if you want advertise self as stub router temporarily on startup.

ospf-stub-router-on-startup-period integer

Specify the time period to advertise self as stub router on startup. This s a value between 5 and 86400 seconds.

ospf-bfd-all-if|no-ospf-bfd-all-if

Specify if you want to use BFD protocol for fault detection on all OSPF interfaces.

ospf-default-information none|originate|always

Specify if you want to control origination of default route.

ospf-default-info-originate-metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-metric-type 1|2

Specify the metric type for OSPF origination of default route.

ospf-redist-connected-metric none

Specify a connected metric type for OSPF route redistribution.

ospf-redist-connected-metric-type 1|2

Specify a connected metric type for OSPF route redistribution.

ospf-redist-rip-metric none

Specify a RIP metric type for OSPF route redistribution.

ospf-redist-rip-metric-type 1|2

Specify a RIP metric type for OSPF route redistribution.

ospf-redist-bgp-metric none

Specify a BGP metric type for OSPF route redistribution.

ospf-redist-bgp-metric-type 1|2

Specify a BGP metric type for OSPF route redistribution.

ospf6-redistribute static|connected|bgp4

Specify if you want to redistribute OSPF6 routes.

ospf6-redist-static-metric none

Specify a metric for OSPF6 redistribute of static routes.

ospf6-redist-static-metric-type 1|2

Specify a metric type for OSPF6 redistribution of static routes.

ospf6-redist-connected-metric none

Specify a metric for OSPF6 redistribution of connected routes.

ospf6-redist-connected-metric-type 1|2

Specify a metric type for OSPF6 redistribution.

ospf-default-information none|originate|always

Specify how to control the origination of default route.

ospf-default-info-originate-metric none

Specify the metric for OSPF origination of default route.

ospf-default-info-originate-metric-type 1|2

Specify the metric type for OSPF origination of default route.

ospf-default-info-originate-route-map vrouter route-map name   

Specify the route map for OSPF origination of default route.

bgp-snmp|no-bgp-snmp

Enable or disable BGP SNMP MIB.

bgp-snmp-notification|no-bgp-snmp-notification

Enable or disable SNMP notifications for BGP MIBs.

ospf-snmp|no-ospf-snmp

Enable or disable OSPF SNMP MIB.

ospf-snmp-notification|no-ospf-snmp-notification

Enable or disable SNMP notifications for OSPF MIBs.

ospf6-snmp|no-ospf6-snmp

Enable or disable OSPFv3 SNMP MIB.

ospf6-snmp-notification|no-bgp-snmp-notification

Enable or disable SNMP notifications for OSPFv3 MIBs.

ip-snmp|no-ip-snmp

Enable or disable ipForward SNMP MIBs.

no-bgp-redist-static-route-map

Remove route map for BGP static redistribution.

no-bgp-redist-connected-route-map

Remove route map for BGP connected redistribution.

no-bgp-redist-ospf-route-map

Remove route map for BGP OSPF redistribution.

bgp-graceful-shutdown|no-bgp-graceful-shutdown

Specify to enable or disable BGP graceful shutdown (RFC 8326).

Defaults   None.

Access   CLI

History   

Version 1.2

Command introduced.

Version 2.0

Parameter type added.

Version 2.2

The parameter, location, hw-router-mac, and hw-vrrp-id, added. The parameters, bgp-redistribute, rip-redistribute, and ospf-redistribute, added.

Version 2.2.3

The parameters bgp-redist and ospf-dist added. The parameter vrrp-track-port added. The parameters bgp-cluster, bgp-max-paths, bgp-multipath, bgp-best-path, bgp-dampening, bgp-graceful-restart, and bgp-stalepath-time added

Version 2.3.1

The parameters, ospf6-, added.

Version 2.4

The parameters, ospf-stub-router-on-startup and vrrp-track-port added. The parameters bgp-scantime, bgp-keepalive-interval, and bgp-holdtime added.

Version 2.4.1

The parameter, bgp-distance-, and ospf-distance-, added.

Version 2.5.4

The parameter, shared-vnet-mgr, added.

Version 2.6

SNMP MIBs for BGP, OSPF, OSPFv3, and ipForward added.

Version 3.0.0

The parameters, ospf-bfd-all-if, ospf-default-information, ospf-default-info-originate, and ospf-default-info-originate-metric-type added.

Version 3.1.0

The parameters for route maps added.

Version 6.1.0

The parameter evpn-border|no-evpn-border added

Version 6.1.1

The parameters evpn-dup-addr-max-moves,  evpn-dup-addr-moves-duration, bgp-update-delay-strict and evpn-dup-addr-freeze added.

Usage   Each fabric, cluster, standalone switch, or virtual network (vNET) can provide its tenants with a virtual router (vRouter) service that forwards traffic between networks and implements Layer 3 protocols. This command displays vRouter service.

Examples  To display the configuration for xyz, use the following command:

CLI (network-admin@switch) > vrouter-show name xyz format all layout vertical

id:                                      c0002ad:0

name:                                    xyz

type:                                    vrouter

scope:                                   fabric

vnet:                                    leo-ext-22-global

vnet-service:                            dedicated

state:                                   enabled

location:                                leo-ext-22

zone-id:                                 c0002ad:1

template:                                no

failover-action:                         stop-old

router-type:                             hardware

fabric-comm:                             false

router-ipstack:                          frr

evpn-border:                             disable

evpn-export-all-leaked-networks:         permit

evpn-dup-addr-freeze:                    180

hw-router-mac:                           66:0e:94:ad:c2:f8

cluster-active-active-routing:           enable

hw-vrid:                                 0

hw-vrrp-id:                              -1

proto-routing:                           static,routesnoop

bgp-redist-static-metric:                none

bgp-redist-connected-metric:             none

bgp-redist-rip-metric:                   none

bgp-redist-ospf-metric:                  none

bgp-max-paths:                           1

bgp-dampening:                           false

bgp-network-import-check:                false

bgp-update-delay-strict(s):              1

bgp-keepalive-interval(s):               60

bgp-holdtime(s):                         180

ospf-spf-consec-delay:                   50

ospf-spf-max-delay:                      5000

ospf6-spf-consecu-delay:                 50

ospf6-spf-max-delay:                     5000

bgp-global-nh-preference:                none

ospf-redist-static-metric:               none

ospf-redist-static-metric-type:          2

ospf-redist-connected-metric:            none

ospf-redist-connected-metric-type:       2

ospf-redist-rip-metric:                  none

ospf-redist-rip-metric-type:             2

ospf-redist-bgp-metric:                  none

ospf-redist-bgp-metric-type:             2

ospf-stub-router-on-startup:             false

ospf-bfd-all-if:                         no

ospf-default-information:                none

ospf-default-info-originate-metric:      none

ospf-default-info-originate-metric-type: 2

bgp-default-shutdown:                    false

bgp-snmp:                                false

bgp-snmp-notification:                   false

ospf-snmp:                               false

ospf-snmp-notification:                  false

ospf6-snmp:                              false

ospf6-snmp-notification:                 false

ip-snmp:                                 false

bgp-graceful-shutdown:                   off 

north
    keyboard_arrow_up
    keyboard_arrow_down
    description
    print
    feedback
    support
    business
    rss_feed
    south