tunnel-show
This command is used to display the list of tunnels on the switch.
Syntax tunnel-show
|
id |
Displays the ID assigned to the tunnel. |
|
scope local |
Displays the scope for the tunnel. Only local scopes are supported. |
|
name name-string |
Displays the name of the tunnel. |
|
type ip-in-ip|vxlan|nvgre |
Displays the type of tunnel. |
|
vnet vnet-name |
Displays the name of the VNET. |
|
vrouter-name vrouter-name |
Displays the name of the vRouter service. |
|
peer-vrouter-name vrouter- name |
Displays the name of the vRouter service on the cluster peer. |
|
local-ip ip-address |
Displays the local IP address. |
|
remote-ip ip-address |
Displays the remote IP address. |
|
router-if vrouter-hw-if-name |
Displays the router interface. |
|
tunnel-if-name tunnel-if-name-string |
Displays the router interface VNIC name. |
|
next-hop ip-address |
Displays the next hop IP address. |
|
next-hop-mac mac-address |
Displays the next hop MAC address. |
|
next_hop_vnet vlan-id |
Displays the next hop VLAN ID. |
|
nexthop-bd bridge-domain |
Next hop bridge domain. |
|
nexthop-vlan 0..4095 |
Next hop VLAN. |
|
remote-switch fabric-node-name |
Displays the remote switch for the tunnel. |
|
vrid vrid-number |
Displays the vRouter hardware ID. |
|
tunnelID tunnelID-number |
Displays the tunnel ID. |
|
interface-mac mac-address |
Displays the MAC address of the tunnel interface. |
|
interface-vnet vnet name |
Displays the VNET name. |
|
bd bridge-domain |
Displays the bridge domain name. |
|
interface-vlan vlan-id |
Displays the interface VLAN. |
|
active yes|no |
Displays the status of the tunnel. |
|
state init|ok|error |
Displays the state of the tunnel. |
|
bfd|no-bfd |
Displays if BFD is configured. |
|
bfd-state unknown|admin-down|down|init|up|no-session|not-replicator-vtep |
Displays the state of the BFD session.D |
|
peer-bfd-state unknown|admin-down|down|init|up|no-session|not-replicator-vtep |
Displays the peer BFD session state. |
|
error error-string |
Displays tunnel errors. |
|
route-info route-info-string |
Displays route information. |
|
ecmp-group ecmp-group-number |
Displays ECMP group information. |
|
using-vxlan-loopback yes|no |
Displays using VXLAN loopback. |
|
ports port-list |
Displays the port list. |
|
nh-egress-id nh-egress-id-number |
Displays the nexthop port egress ID. |
|
flood-nh-ip ip-address |
Flood next hop IP address. |
|
flood-nh-vlan 0..4095 |
Flood next hop VLAN ID. |
|
flood-nh-port flood-nh-port-number |
Flood next hop port number. |
|
flood-nh-mac mac-address |
Flood next hop MAC address. |
|
flood-nh-egress-id flood-nh-egress-id-number |
Flood next hop hardware egress ID. |
|
auto-tunnel auto|static |
Displays if the tunnel is automatic or static. |
|
ecmp-nexthops|no-ecmp-nexthops |
Filter single or multiple route entries per nexthops. |
|
flood-nexthop|no-flood-nexthop |
Displays tunnels with either flood-nexthop or with no-flood-nexthop configured. |
|
mac-learning|no-mac-learning |
Displays tunnels with either MAC learning enabled or MAC learning disabled. |
Defaults None.
Access CLI
History
|
Version 1.2 |
Command introduced. |
|
Version 2.2.2 |
The parameter, type, added. |
|
Version 2.2.3 |
The parameter router-if replaced name-string with vrouter-hw-if name option. |
|
Version 2.3.1 |
The parameter, active, added. |
|
Version 2.4 |
The option, cluster, added to scope. The parameters, vrouter-name and peer-vrouter-name, state, error, route-info, and ecmp-group added. |
|
Version 2.5 |
The parameter, vnet, added. |
|
Version 3.0.0 |
The parameter, vrouter-if, deprecated. The parameter, bfd, added. |
|
Version 6.0.0 |
The parameter, mac-learning, added. |
Usage Tunnels are used to encapsulate unsupported protocols on a network. Use this command to display a list of tunnels on a fabric.
Examples To display a list of all tunnels on a switch, use the following command:
CLI network-admin@switch > tunnel-show