fabric-comm-vrouter-bgp-create
This command is used to create a fabric over a Layer 3 network using a BGP vRouter.
Syntax fabric-comm-vrouter-bgp-create
|
name name-string |
Specify the name of the fabric communication vRouter. |
|
bgp-as number |
Specify the BGP Autonomous System number from 1 to 4294967295. |
|
bgp-redistribute static|connected|rip|ospf |
Specify the BGP route redistribution type. |
|
bgp-max-paths integer |
Specify the maximum BGP paths from 1 to 255. |
|
bgp-ibgp-multipath integer |
Specify the number of IBGP multipath connections from 1 to 255. |
|
router-id ip-address |
Specify the vRouter ID. |
|
hw-vrrp-id hw-vrrp-id-number |
Specify the VRRP ID assigned to the hardware router. |
|
bgp-nic-ip ip-address |
Specify the IP address. |
|
bgp-nic-netmask netmask |
Specify the netmask. |
|
bgp-nic-linklocal ip-address |
Specify the IPv6 link local address. |
|
bgp-nic-vnet vnet name |
Specify the VLAN interface. |
|
bgp-nic-bd bridge-domain name |
Specify the bridge domain interface. |
|
bgp-nic-vlan vlan-id |
Specify the VLAN ID. |
|
bgp-nic-vlan-type public|private |
Specify the VLAN type as public or private. |
|
bgp-nic-l3-port l3port-usable-port name |
Specify the Layer 3 port. |
|
in-band-nic-ip ip-address |
Specify the IP address of the in-band management interface. |
|
in-band-nic-netmask netmask |
Specify the netmask of the in-band management interface. |
|
in-band-nic-linklocal ip-address |
Specify the IPv6 link local address. |
|
in-band-nic-vnet vnet name |
Specify the VLAN interface. |
|
in-band-nic-bd bridge-domain name |
Specify the bridge domain interface. |
|
in-band-nic-vlan vlan-id |
Specify the VLAN interface. |
|
in-band-nic-if-nat-realm internal|external |
Specify the NAT interface realm. |
|
neighbor ip-address |
Specify the IP address of the BGP neighbor. |
|
remote-as integer |
Specify the BGP remote AS from 1 to 4294967295. |
|
next-hop-self|no-next-hop-self |
Specify the next hop as self or not. |
|
password password-string |
Specify the MD5 password for BGP. |
|
ebgp-multihop integer |
Specify the value for external BGP from 1 to 255. |
|
update-source-interface update-source-interface-string |
Specify the interface name of BGP packets. This parameter is required for peering over any interface. |
|
override-capability|no-override-capability |
Specify if you want override capability. |
|
soft-reconfig-inbound|no-soft-reconfig-inbound |
Specify if you want a soft reset to reconfigure inbound traffic. |
|
max-prefix max-prefix-number |
Specify the maximum number of prefixes. |
|
max-prefix-warn-only|no-max-prefix-warn-only |
Specify you want to receive a warning if the maximum number of prefixes is exceeded. |
|
bfd|no-bfd |
Specify if you want BFD protocol support for fault detection. |
|
weight none |
Specify the weight value between 0, and 65535 for the neighbor's routes. The default is none. |
|
default-originate|no-default-originate |
Specify to announce default routes to the neighbor or not. |
|
neighbor-keepalive-interval seconds |
Specify the keepalive interval in seconds. This is a value between 0, and 65535 seconds. |
|
neighbor-holdtime seconds |
Specify the neighbor hold time in seconds. This is a value between 0, and 65535 seconds |
|
allowas-in|no-allowas-in |
Specify if you want to reject routes with local AS in AS_PATH. Normally, when you do not set this option, nodes reject routes containing their own AS which helps prevent routing loops. However, in some cases nodes that belong to the same AS have no direct connectivity; for example when you form clusters, and choose not to use the cluster link for iBGP communication. In this case the only way to direct routes through connected eBGP neighbors is to set this option so routes are not rejected routes from the cluster peer. |
|
interface vrouter interface nic |
Specify the interface to reach the neighbor. |
|
advertisement-interval 0..600 |
Specify the minimum interval between sending BGP routing updates. |
|
no-route-map-in |
Specify if you want to remove an ingress route map. |
|
no-route-map-out |
Specify if you want to remove an egress route map. |
|
fabric-network ip-address |
Specify the in-band network IP address. |
|
fabric-netmask netmask |
Specify the in-band network mask. |
Defaults None
Access Network administrator
History
|
Version 2.4.1 |
Command introduced. |
|
Version 2.5.2 |
The parameter allowas-in|no-allowas-in added. |
|
Version 3.0.0 |
The parameter interface added. |
|
Version 3.1.0 |
The parameters advertisement-interval, no-route-map-in, and no-route-map-out added. |
|
Version 6.0.1 |
The parameter update-source-interface added. |
Usage This command is used to allow fabric communication over a Layer 3 network.
Examples To modify fabric communication ports, use the following syntax:
CLI (network-admin@switch) > fabric-comm-vrouter-bgp-create