port-phy-show

Glossary		Print Page		Document Feedback		Support & Services		Pluribus Networks		Pluribus Blog		LinkedIn		Facebook		Twitter

port-phy-show

This command is used to display information about the physical Layer 1 status of the local switch.

Syntax port-phy-show

port port-list	Specifies the switch network data port number, range or list of ports. Range for port numbers is from 1 to 64.
bezel-port bezel-port-string	The bezel port.
state off\|admin-down\|adminpwrdown\|bist\|dfe-tuning\|down\|local-fault\|partially-up\|remote-fault\|up\|failed	The state of the port PHY.
mode off\|admin-down\|adminpwrdown\|bist\|dfe-tuning\|down\|local-fault\|partially-up\|remote-fault\|up\|failed	The mode of the port PHY.
autoneg autoneg-string	The auto-negotiation setting of the port PHY.
speed speed-number	The speed of the port PHY.
eth-mode configured 1000base-x\|sgmii\|disabled\|1000base-kx\|2500base-x\|6Gbase-kr\|6Gbase-cr\|10Gbase-kr\|10Gbase-cr\|10Gbase-sr\|AN-73\|Xaui\|10Gbase-kx4\|10Gbase-cx4\|24Gbase-kr4\|24Gbase-cr4\|40Gbase-kr4\| XLaui\|40Gbase-cr4\| 40Gbase-sr4\|no-phy-present\|MII\|GMII\|TBI\|10G-XGMII\|1G-RGMII\|sfi\|xfi\|cx\|kr4\|sr4\|lr4\|er4\|cr4\|cx4\|kx4\|caui4\|kr2\|er2\|cr2\|sr2\|lr2\|xlaui2\|cx2\|sr\|lr\|er\|cr\|kx\|kr\|zr\|base-x\|sys-default\|caui\|aoc\|xlppi\|psm4\|base_t\|base_cx\|base_lx\|base_sx\|10G-SFI\|10G-XFI\|GMII	Specify the Ethernet mode as 1000 base or Serial Gigabit Media Independent Interface (SGMII).
max-frame max-frame-number	The maximum number of frames.
def-vlan def-vlan-number	The default VLAN identifier of the port PHY.
dfe-mode static\|one-shot\|continuous\|kr	The DFE mode.
dfe-coarse not-started\|in-progress\|complete\|error	The DFE coarse state.
dfe-fine not-started\|in-progress\|complete\|error	The DFE fine state.
fec fec-string	The forward error correction (FEC).

Defaults None.

Access CLI

History

Version 1.2	Command introduced.
Version 2.1	The parameter eth-mode added.
Version 2.2	The options, disabled\|1000base-kx\|2500base-x\|6Gbase-kr\|6Gbase-cr\|10Gbase-kr\|10Gbase-cr\|10Gbase-sr\|AN-73\|Xaui\|10Gbase-kx4\|10Gbase-cx4\|24Gbase-kr4\|24Gbase-cr4\|40Gbase-kr4\| XLaui\|40Gbase-cr4\|40Gbase-sr4\|no-phy-present\|MII\|GMII\|TBI\|10G-XGMII\|1G-RGMII\|10G-SFI\|10G-XFI added.
Version 3.0.0	The parameter link-quality deprecated.
Version 3.1.0	The parameters GII, and disabled added.
Version 7.0.0	The parameter bezel-port added.

Usage Switches are equipped with network data ports for host or inter-switch communication. Use this command to display the status of network data ports on the local switch.

Examples To display the status of network data ports on the switch, use the following command:

CLI (network-admin@switch) > port-phy-show

switch port state speed eth-mode max-frame def-vlan

------ ---- ----- ----- --------- --------- --------

switch 1 down 10000 xfi 1540 1

switch 2 down 10000 xfi 1540 1

switch 3 down 10000 xfi 1540 1

switch 4 down 10000 xfi 1540 1

switch 5 down 10000 xfi 1540 1

switch 6 down 10000 xfi 1540 1

switch 7 down 10000 xfi 1540 1

switch 8 down 10000 xfi 1540 1

switch 9 down 10000 xfi 1540 1

switch 10 down 10000 xfi 1540 1

switch 11 down 10000 xfi 1540 1

switch 12 up 10000 xfi 1540 1

switch 13 down 10000 xfi 1540 1

switch 14 down 10000 xfi 1540 1

switch 15 down 10000 xfi 1540 1

switch 16 down 10000 xfi 1540 1

switch 17 down 10000 xfi 1540 1

switch 18 down 10000 xfi 1540 1

switch 19 down 10000 xfi 1540 1

switch 20 down 10000 xfi 1540 1

switch 21 down 10000 xfi 1540 1